Intelbras LSWM2SP2PB Interface Cards User Manual

Intelbras LSWM2SP2PB Interface Cards

Overview

The LSWM2SP2PB interface card provides two SFP+ ports.

LSWM2SP2PB

LSWM2SP4PB

The switch models that the LSWM2SP2PB & LSWM2SP4PB interface cards are applicable to might change over time. For the most up-to-date list of applicable switch models, contact Intelbras Support or marketing staff.

The restrictions for using the LSWM2SP2PB and LSWM2SP4PB vary bydevice model. For more information, see the installation guide for the device.

Installing and removing the card

• The installation and removal procedures are the same for the LSWM2SP2PB and LSWM2SP4PB interface cards. This section uses the LSWM2SP2PB interface card as an example.
• Prepare the following tools before you install or remove the card: Phillips screwdriver, flat-blade screwdriver, and ESD wrist strap.
• No installation tools are provided with the device. Prepare these tools yourself.

1. Safety precautions

   • Before you install or remove the card, wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably grounded.
   • To avoid device damage, do not use excessive force when you install or remove the card.

2. Installing the card
   Remove the filler panel (if any) from the target slot before installing the card.
   Keep the removed screw and filler panel secure for future use.
   

3. Unpack the card. Insert the card slowly into the slot along the guide rails.

4. Rotate inward the ejector lever until the card is in close contact with the switch.

5. Use a Phillips screwdriver to tighten the captive screw on the card.

6. Removing the card
   To avoid cable damage, remove the cables from the card before removing the card.
   If you are not to install a new card after removing the original one, install a filler panel in the slot to prevent dust and ensure good ventilation in the device.
   Place the removed card on an anti-static mat or in an anti-static bag.
   

7. Use a Phillips screwdriver to loosen the captive screw on the card.

8. Hold the ejector lever to pull the card outward until the card is disconnected from the connectors.

9. Hold the card with both hands and take it out slowly.

Verifying the installation

After the installation is complete, determine whether the card is operating correctly. If the card fails to operate correctly, perform the following steps:

• Reinstall the card following the installation procedures described in this document.
• If the problem persists, contact Intelbras Support.

Ports

• You can install SFP/SFP+ modules and SFP/SFP+ network cables in the SFP+ ports.
• The SFP-GE-LX-SM1310-BIDI and SFP-GE-LX-SM1490-BIDI transceiver modules must be used in pairs.
• Intelbras transceiver modules and cables available for the card are subject to change over time. For the most recent list of Intelbras transceiver modules and cables available for the card, contact Intelbras Support or marketing staff.

Model| Central wavelength| Connector| Cable specifications| Modal bandwidth (MHzkm)| Max transmission distance
---|---|---|---|---|---
10-GE SFP+ transceiver modules 10G SFP+
SFP-XG-LX-SM1310-E| 1310 nm| LC| 9/125µm SMF| –| 10km (6.21 miles)
SFP-XG-SX -MM850-E| 850 nm| LC| 50/125µm MMF| 2000| 300m (984.25 ft)
500| 82m (269.03 ft)
400| 66m (216.54 ft)
| | | 62.5/125µ| 200| 33m (108.27 ft)
Model| Central wavelength| Connector| Cable specifications| Modal bandwidth (MHzkm)| Max transmission distance
---|---|---|---|---|---
| | | mMMF| 160| 26m (85.30 ft)
SFP-XG-LH40-SM1550| 1550 nm| LC| 9/125µm SMF| –| 40 km (24.86 miles)
SFP-XG-LH80-SM1550| 1550 nm| LC| 9/125µm SMF| –| 80 km (49.71miles)
Gigabit SFP transceiver modules
SFP-GE-T| –| RJ-45| UTP/STP| –| 100 m (328.08ft)
SFP-GE-SX -MM850-A| 850 nm| LC| 50/125µm MMF| 500| 550 m (1804.46ft)
400| 550 m (1804.46ft)
62.5/125µ mMMF| 200| 275 m (902.23ft)
160| 220 m (721.78ft)
SFP-GE-LX-SM1310-A| 1310 nm| LC| 9/125µm SMF| –| 10 km (6.21miles)
50/125µm MMF| 500 or 400| 550 m (1804.46ft)
62.5/125µ mMMF| 500| 550 m (1804.46ft)
SFP-GE-LH40-SM1310| 1310 nm| LC| 9/125µm SMF| –| 40 km (24.86miles)
SFP-GE-LH40-SM1550| 1550 nm| LC| 9/125µm SMF| –| 40 km (24.86miles)
SFP-GE-LH80-SM1550| 1550 nm| LC| 9/125µm SMF| –| 80 km (49.71miles)
SFP-GE-LH100 SM1550| 1550 nm| LC| 9/125µm SMF| –| 100 km (62.14miles)
SFP-GE-LX-SM1310-BIDI|

• Transmitting end (TX): 1310
• Receiving end(RX): 1490

| LC| 9/125µm SMF| –| 10 km (6.21miles)
Model| Cable length| Data rate
---|---|---
10-GE SFP+ copper cables
LSW 1STK| 0.65 m (2.13 ft)| 10 Gbps
LSWM2STK| 1.2 m (3.94 ft)|
---|---|---
LSW 3STK| 3 m (9.84 ft)
LSTM 1STK| 5 m (16.40 ft)
Gigabit SFP copper cables
SFP-STACK-Kit| 1.5 m (4.92 ft)| 1250 Mbps

LEDs

The SFP+ port LEDs are not affected by the port LED mode switching button on your switch.
For more information about the port LED mode switching button, see the installation guide for the switch.

operating at 10 Gbps, and a link is present on the port.
Flashing green| The port is sending or receiving data at 10 Gbps.
Steady yellow| A transceiver module is installed in the port. The port is operating at 1 Gbps, and a link is present on the port.
Flashing yellow| The port is sending or receiving data at 1 Gbps.
Off| No transceiver module is installed in the port, or no link is present on the port.

SWM2SP2PB Box Content: 1 x Interface Card – 2 SFP+ ports
LSWM2SP4PB Box Content: 1 x Interface Card – 4 SFP+ ports

Compatible with: SC 5520 Series, SC 5525-24X-2QE, SC 5525-48X-2QE, SC 5525 -24X-2HE, SC 5525-48X-2HE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>