FORMAX FD 8304CC Shredder

Specifications:

• Cutting Style: Cross Cut
• Shred Size: 1/16 x 19/32
• Sheet Capacity: 6 – 7 sheets
• Speed: 26 feet per minute
• Feed Opening: 10.5″
• Dimensions: 16.5″ W x 15.3″ D x 28.7″ H
• Bin Capacity: 10.5 gal.
• Weight: 108 lbs.
• Power supply: 110V, 50/60Hz
• Accepts: staples and paper clips
• Sheet capacity varies depending on paper and power supply

Set-up Guidelines:

1. Install the shredder on a level surface, away from heat sources and direct sunlight.
2. Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet is shared with another electronic device, the total current should not exceed 30A (at 110V).

Operation:

Flip the power switch ON located on the right side of the shredder.

1. Auto Start/Auto Stop: When the START button is pushed, the AUTO LED will light. Insert paper to be shredded. The shredder will start and stop automatically when using this function.
2. Reverse Operation: Push the REV button and the REV LED will light, and cutters will operate in reverse. If too much paper is inserted at one time, the shredder will automatically operate in reverse. Remove excess paper and shred in smaller amounts.
3. Note: Do not exceed half of the maximum capacity if using the shredder continuously.
4. Full Sensor: If the waste bin is full, the FULL LED will light, and the cutter will stop automatically. Open the door, empty and replace the waste bin, close door, and continue to shred.

Safety Precautions:

To avoid personal injury and damage to the shredder, observe the following safety precautions. Keep these instructions for future reference.

In case of emergency, flip the Power Switch to cut off power and/or pull the plug out of the wall outlet.

FAQ

• Q: How often should I oil the cutting blades?
  • A: For peak performance, it is recommended to oil the shredder blades after every 4 hours of operation using a cutting head lubricating oil like Formax part #8000-10.
• Q: What should I do if the shredder stops operating due to too much paper?
  • A: Reduce the amount of paper inserted, remove excess paper, and resume shredding.
• Q: How do I know when the waste bin is full?
  • A: The FULL LED will light up when the waste bin is full, indicating that it’s time to empty it before resuming operation.

Features

Automatic Reverse Rotation

When too much paper is inserted, the cutter stops operating andautomatically rotates in reverse to discharge the jammed paper. The shredder will beep. Reduce the amount of paper and resume shredding

Door Switch

If the door is open, the shredder will not operate.

Automatic Stop

When the waste bin is full, the “FULL” LED will light and the cutter stops operation. Open the door, remove the waste bin and empty. Replace the waste bin, close the door, and press START to resume operation.

Automatic Power Shut-Off

If the shredder operates continuously for more than 30 minutes, the power is automatically shut off.

Oiling the Cutting Blades

For peak performance, Formax recommends oiling the shredder blades after every 4 hours of operation. Use a cutting head lubricating oil like Formax part

8000-10.

To oil : Spread a small amount of shredder oil onto the cutters through the feed opening, and allow the oil to sit for a few minutes to permeate the cutting blades, then press the “REV” button and hold for five seconds. The “REV” LED indicator on control panel will light. The shredder will operate in reverse for one minute, then the “AUTO” LED will light indicating the shredder is ready for use.

Operator Maintenance

• Disconnect power by pulling power cord plug from wall outlet.
• To clean the exterior, wipe the surface with a soft cloth. If the surface is very dirty, use a neutral detergent, then wipe again with a soft cloth.

CAUTION:

• Never put water directly on the surface of the shredder.
• Never clean the case with benzene or thinner, since it will cause discoloration.
• Do not dismantle the shredder. Contact your Formax Dealer for service.

Specifications

Sheet capacity varies depending on paper and power supply

Set-up Guidelines

1. Install the shredder on a level surface, away from heat sources and direct sunlight.
2. Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet is shared with another electronic device, the total current should not exceed 30A (at 110V).

Operation

• *  Flip the power switch “ON” located on the right side of the shredder.

• Auto Start/Auto Stop
  • When the START button is pushed, the “AUTO” LED will light. Insert paper to be shredded. The shredder will start and stop automatically when using this function.
• Reverse Operation
  • Push the REV button and the “REV” LED will light and cutters will operate in reverse. If too much paper is inserted at one time, the shredder will automatically operate in reverse. If this occurs, remove the inserted paper and shred in smaller amounts.
  • NOTE : The maximum amount of paper to be shredded differs according to paper quality, humidity and voltage. If the shredder is to be used continuously, do not insert more than half of the maximum capacity.
• Full Sensor
  • If the waste bin is full, the “FULL” LED will light and the cutter will stop automatically. Open the door, empty and replace the waste bin, close door, and continue to shred.

Safety Precautions

To avoid personal injury, and damage to the shredder, observe the following safety precautions. Please keep these instructions for future reference.

NOTE: In case of emergency, flip the “Power Switch” to cut off power and/or pull the plug out of the wall outlet.

• Keep hands, long hair, clothing, ties, jewelry and loose items away from the feed opening and shred outlet.
• Do not use the shredder for anything other than its intended purpose. Never use  it to shred cloth, plastic, cardboard or any hard material that will cause damage tothe shredder blades.
• Do not allow children to use the machine.
• Do not operate with a damaged power cord or plug, or if the machine is damaged in any manner.
• Unplug the shredder when it is being moved, or if it is not in use for an extended period of time.
• Do not disconnect the power by pulling only the cord. Hold the plug when disconnecting.
• Keep the shredder away from direct sunlight.
• Do not sit on the shredder or place anything on top of it.
• Never open the fixed switch or cover.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>