CTA ADD-PARAFSV Premium Floor Stand Kiosk Installation Guide
- June 15, 2024
- CTA
Table of Contents
CTA ADD-PARAFSV Premium Floor Stand Kiosk
Product Information
- Specifications
- Product Name: Premium Floor Stand Kiosk with Graphic Slots & VESA Plate for Kitting (Black)
- Model Number: ADD-PARAFSV
Product Usage Instructions
- Installing Base
- To install the base of the floor stand, follow these steps:
- Align the base plate (A) with the body (J).
- Rotate in the screw (F) from the bottom using the provided Allen key tool (C).
- Setting Up Graphic Card Slot
- To set up the graphic card slot, follow these steps:
- Slide out the (2) graphic card panels in the front and back of the body (J). If there is a sticker film, remove it first.
- If you have printed out a sticker graphic, place it onto the panel. If you are using a complete new panel, you can replace the initial panels that came with the floor stand. Place one panel back first, then the other.
- Setting Up Cable Routing
- To set up cable routing, follow these steps:
- With only (1) panel back in, slide in the power cords and any other cords that need to be connected to the tablet through the body.
- There will be gaps at the top and bottom for them to route out to the power source and to the device. Slide in the second panel when routing is finished.
- Align VESA Plate and Front Plate Component with Floor Stand
- To align the VESA plate and front plate component with the floor stand, follow these steps:
- Align the VESA plate base (B) with the front plate base (D) to the top of the floor stand (J).
- Make sure all the holes are aligned and ready for installation.
- Attach VESA Plate
- To attach the VESA plate, follow these steps:
- First, with all the items aligned, route any wires through the plate’s openings.
- Then rotate in screws (G) and washers (E) from the top using the provided tool (C) as illustrated.
- FAQ
- Q: How do I replace the initial graphic card panels that came with the floor stand?
- A: To replace the initial graphic card panels, simply remove them and replace them with the new panels. Make sure to align them properly and remove any sticker film before placing the new graphic.
- Q: Can I route multiple cords through the body of the floor stand?
- A: Yes, you can route multiple cords through the body of the floor stand. There are gaps at the top and bottom for the cords to route out to the power source and to the device.
- Q: How do I align the VESA plate and front plate component with the floor stand?
- A: To align the VESA plate and front plate component, place the VESA plate base (B) and front plate base (D) to the top of the floor stand (J). Make sure all the holes are aligned for proper installation.
CONTENTS
INSTALLATION
- INSTALLING BASE:
- SETTING UP GRAPHIC CARD SLOT
- 2A. SLIDE OUT THE (2) GRAPHIC CARD PANELS IN THE FRONT AND BACK OF THE BODY (J). IF THERE IS A STICKER FILM, REMOVE THAT FIRST. IF YOU HAVE PRINTED OUT A STICKER GRAPHIC, PLACE IT ONTO THE PANEL. IF YOU ARE USING A COMPLETE NEW PANEL, YOU CAN REPLACE THE INITIAL PANELS THAT CAME WITH THE FLOOR STAND. PLACE ONE PANEL BACK FIRST, THEN THE OTHER.
- 2A. SLIDE OUT THE (2) GRAPHIC CARD PANELS IN THE FRONT AND BACK OF THE BODY (J). IF THERE IS A STICKER FILM, REMOVE THAT FIRST. IF YOU HAVE PRINTED OUT A STICKER GRAPHIC, PLACE IT ONTO THE PANEL. IF YOU ARE USING A COMPLETE NEW PANEL, YOU CAN REPLACE THE INITIAL PANELS THAT CAME WITH THE FLOOR STAND. PLACE ONE PANEL BACK FIRST, THEN THE OTHER.
- SETTING UP CABLE ROUTING
- 3A. WITH ONLY (1) PANEL BACK IN, SLIDE IN THE POWER CORDS AND ANY OTHER CORDS THAT WOULD NEED TO BE CONNECTED TO THE TABLET THROUGH THE BODY AS SHOWN. THERE WILL BE GAPS AT THE TOP AND BOTTOM FOR THEM TO ROUTE OUT TO THE POWER SOURCE AND TO THE DEVICE. SLIDE IN SECOND PANEL WHEN ROUTING IS FINISHED.
- 3A. WITH ONLY (1) PANEL BACK IN, SLIDE IN THE POWER CORDS AND ANY OTHER CORDS THAT WOULD NEED TO BE CONNECTED TO THE TABLET THROUGH THE BODY AS SHOWN. THERE WILL BE GAPS AT THE TOP AND BOTTOM FOR THEM TO ROUTE OUT TO THE POWER SOURCE AND TO THE DEVICE. SLIDE IN SECOND PANEL WHEN ROUTING IS FINISHED.
- ALIGN VESA PLATE AND FRONT PLATE COMPONENT AND WITH FLOOR STAND
- 4A. ALIGN THE VESA PLATE BASE (B) WITH THE FRONT PLATE BASE (D) TO THE TOP OF THE FLOOR STAND (J). MAKE SURE ALL THE HOLES ARE ALIGNED AND READY FOR INSTALLATION.
- 4A. ALIGN THE VESA PLATE BASE (B) WITH THE FRONT PLATE BASE (D) TO THE TOP OF THE FLOOR STAND (J). MAKE SURE ALL THE HOLES ARE ALIGNED AND READY FOR INSTALLATION.
- ATTACH VESA PLATE
- 5A. FIRST, WITH ALL THE ITEMS ALIGNED, ROUTE ANY WIRESTHROUGH THE PLATE’S OPENINGS.
- 5B. THEN ROTATE IN SCREWS(G) AND WASHERS(E) FROM THE TOP USING PROVIDED TOOL (C) AS ILLUSTRATED.
CONTACT
- 36 Taaffe Place Brooklyn, NY 11205
- support@ctadigital.com.
- 888-733-4448
- www.ctadigital.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>