DIGITALas D-FORCE INOX ST 6000 Tripod Turnstile Instruction Manual
- October 30, 2023
- DIGITALas
Table of Contents
DIGITALas D-FORCE INOX ST 6000 Tripod Turnstile Instruction Manual
Note: Before operating this unit, please read this instruction
completely.
Thank you for choosing tripod turnstile; this is a product with high
technology, so please read this manual carefully before operation. Please keep
this manual for future reference. Only trained professionals who understand
electric and mechanical risk of product are qualified to install and operate
gate system so as to avoid unnecessary dangers caused by misoperation. All
rights to improve and perfect our products are reserved. We can’t promise
thismanual is in full accord with the product you receive, but we will check
and revise the manual at regular interval. No further notification will be
sent in the case of any modifications to the manual.
Product introduction
Function Features
- Standard signal input port, can be connected with most of the access control board, fingerprint device and scanner other equipment;
- Automatic reset function, if people swipe the authorized card, but don’t pass through within the settled time, it need to swipe card again for entry;
- Card-reading Recording function
- Automatic opening after emergency fire signal input
- Anti following : prevent illegal passing
- High light LED indicator , displaying passing status.
- Normal open can be also controlled via external button or manual key unlock .
- Arm will automatically fall down when power failure
Technical parameter
Item | Description |
---|---|
House | 304 stainless steel |
Reliability of the core | 3million, no fault |
Weight | 55Kg(bridge type) |
Arm length | 510(mm) |
Max thrust capacity | 60Kg |
Driving force of arms | 3Kg |
Driving mode | digital |
Direction of rotation | Unidirectional/ Bidirectional (controllable) |
Indicator lamp | Green means passage |
Power supply for core: | AC100~220V |
Operational voltage | DC 24V ±5% |
Voltage of indicator lamp: | DC12V ±5%(standard) |
Power consumption | 30W |
Working environment | Indoors or outdoors(outdoor is optional) |
Working temperature | -30℃~60℃ |
Humidity | 5%~90% |
Waterproof | ≧IP31 |
Installation interfaces for card readers: | 2 |
Control interface | relay signal input |
Time needed for opening | 0.2 seconds |
Passing speed | 30~45 persons/min |
Product structure
The structure of the product is mainly composed of mechanical and electric
control system.
Note: Configurethe mechanism type according to the product series and model…
The electric control system consists of access control device, control board, direction indicator, position sensor, SFsolenoid, damper,power supply.
NO | Name | Function |
---|---|---|
1 | Access control device | IC/ID card access control, fingerprint, face |
recognition, codereader, access control device send delay signal to the
turnstile board door signal(It is available according to actual use)
2| Control board| The control center of the system, when receiving the access
control device delay signal, it control solenoid open ,the direction indicator
light turns green, The arm can be pushed to 120 degree ,the solenoid will lock
immediately when receivingclosing signal from mechanism position sensor.
3| Indicator| Display the current channel status
4| Position sensor| Detects and controls the opening and closing position of
the gate
5| Square solenoid| Control shatf close or open
6| Circular solenoid| Falling and upper arm
7| Damper| Makes the shaft run smoothly(match)
8| Power Supply| power supply to control board
Equipment Installations
Installation notes
- If it tests well before installation, then fixed it; before you install and maintain it, please cut off the power;
- The product must be earthed, and an earth leakage breaker is necessary on the power supply;
- The depth of buried PVC tube should be greater than 60mm, and the exposed height above the ground should be greater than 50mm. The exit mouth should be bending back to avoid water dipping inside the tube;
- Don’t change the inside wire of the turnstile casually;
- In installation, please make each door of the lane are in alignment;
- Tighten the mounting screws of the arm ;
- If you use the turnstile outdoor, it need to add a canopy to protect the turnstile from sun and rain;
Equipment Installation
-
Tool preparations
1| A set of hexagon spanner| 5| Screw driver and other common wiring tool
---|---|---|---
2| Cross screwdriver 6mm| 6| Millimeter
3| Open spanner 17-19mm| 7| M10x100 Expansion screws 8pcs
4| Impact drill D14| 8| Cable Tester -
Ensure the installation location and the system composition ,prepare to install after carrying out the system planning;
-
Make well of installation of equipment foundation .
-
Mark the fixing position of expansion bolts according to fixing plate on the bottom of each turnstile.
-
Drill hole by impact drill, fix Expansion screws.
-
Fix arm :Before delivery, we will dismantle three arm bar, so before using turnstileYou should assemble arm bar like following picture.
-
Tighten the expansion screw after the functional test is completed.
Connection
- Connecting AC100~220V power input
- onnect wire of access control device
Notice of use
- Please keep the control button or remote control far away from the children;
- Please don’t use the turnstile under the thunder and lightning condition to get rid of damage to the equipment.
- Do not permit children to play on or around a turnstile . If child want to go through the turnstile, the parents must look after them.
Control Board and wiring diagram
Control Board instruction
No | Port Sign | Instructions |
---|---|---|
1 | +24V | 24V input power supply to PCB board (Power in) |
2 | GND | |
3 | +12V | 12V power Output (Reserved 12V port) |
4 | GND | |
5 | D1Ex | (Reserved port) |
6 | D2Ex | |
7 | Man1 | Entrance direction button for manual opening gate input |
8 | GND | |
9 | Man2 | Exit direction button for manual opening gate input |
10 | GND | |
11 | A+ | 485 communication |
12 | B – |
Wiring Diagram
DIP switch instructions
1-6 DIP indication | Automatic reset times | 8 DIP |
---|---|---|
6 | 5 | 4 |
0 | 0 | 0 |
0 | 0 | 0 |
0 | 0 | 0 |
0 | 0 | 0 |
0 | 0 | 0 |
0 | 0 | 0 |
0 | 0 | 0 |
0 | 0 | 1 |
0 | 0 | 1 |
0 | 0 | 1 |
0 | 0 | 1 |
0 | 0 | 1 |
0 | 0 | 1 |
0 | 0 | 1 |
0 | 0 | 1 |
0 | 1 | 0 |
0 | 1 | 0 |
0 | 1 | 0 |
0 | 1 | 0 |
0 | 1 | 0 |
0 | 1 | 0 |
0 | 1 | 0 |
0 | 1 | 0 |
0 | 1 | 1 |
0 | 1 | 1 |
0 | 1 | 1 |
with memory function, if swiping valid card 5 times, it can pass five peoples; without memory function, if swiping valid card 5 times, it only can pass one people.
Warranty Service Statement
Our company products are guaranteed for one year, from date of sale, providing free maintenance based on not being damaged by any man-made.
- During the warranty period, all faults caused by the product itself can be maintained for free. Please carry the filled warranty card and the purchase invoice to the authorized service centers across the country or return the machine to our company for free repair.
- Within the period of free maintenance, faults or damages caused by man-made or natural disasters can be maintained with additional charge.
- Over the period of free maintenance, faults or damages can be maintained with additional charge.
The following conditions are not under warranty:
- Damages caused by abnormal operation, man-made or natural disasters;
- Damages after disassembling any portion of the machine (lines, components etc.) ;
- Damages caused by wrong guide of non-professional technicians;
- Damages caused by adding other functions with unauthorized modification or installation with other equipment.
Note: The warranty card and purchase invoice are used as warranty certificates to maintain the machine. Please reserve them carefully. Lose won’t repair.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>