CZONE 80-911-0216-00 Touch 10 Generation 2 Display Kit User Manual

June 6, 2024
CZONE

CZONE logo

CZONE 80-911-0216-00 Touch 10 Generation 2 Display Kit

CZONE 80-911-0216-00 Touch 10 Generation 2 Display Kit

Copyright
This document is copyright 2020 under the Creative Commons agreement. Rights are granted to research and reproduce elements of this document for non- commercial purposes on the condition that CZone is credited as the source. Electronic re-distribution of the document in any format is restricted, to maintain quality and version control.

Important
CZone strives to ensure all information is correct at the time of printing. However, the company reserves the right to change without notice any features and specifications of either its products or associated documentation.
Translations: In the event that there is a difference between a translation of this manual and the English version, the English version should be considered the official version.
It is the owner’s sole responsibility to install and operate the device in a manner that will not cause accidents, personal injury or property damage.

General Information

Use Of This Manual
This manual serves as a guideline for the safe and effective operation of the following Touch 10 Generation 2 model:

Description Part number
CZONE TOUCH 10 GEN 2 80-911-0216-00

Liability
CZone can accept no liability for:

  • Consequential damage resulting from the use of the Touch 10.
  • Possible errors in the included manual and the consequences of these.
  • Use that is inconsistent with the purpose of the product.

Disclaimer: Our products are subject to continual development and improvement. Therefore, additions or modifications to the products may cause changes to the technical data and functional specifications. No rights can be derived from this document. Please consult our most current Terms & Conditions of Sale.

Warranty
The CZone product warranty covers the Touch 10 for the first two years after the purchase date, on the condition that the product is installed and used according to the instructions in this manual. Installation or use that do not comply with these instructions may result in under performance, damage or failure of the product and may void this warranty. The warranty is limited to the cost
of repair and/or replacement of the product. Costs of labor or shipping are not covered by this warranty.

Identification Label

Identification Label

Important information required for service or maintenance can be derived from the identification label. The identification label is located on the back of the Touch 10.

CAUTION
Never remove the identification label. This will void the warranty.

Overview

Description
CZone Touch 10 Generation 2 is the gateway to your CZone Digital Switching. The state of the art CZone Touch 10 Generation 2 is a sleek attractive touch screen with glass dash styling that will complement the interior of any high- end vessel or recreational vehicle. Touch 10 Generation 2, has a powerful dual-core processer and easy to use, intuitive CZone 2.0 User Interface with customizable favorites pages, simple controls and easy to follow menu structure. The high bright IPS LCD touch screen panel offers the very latest generation capacitive touchscreen technology to ensure maximum responsiveness. The CZone Touch 10 Generation 2 outperforms in sunlight, is viewable from any angle, and features dimming capability for optimal night-time viewing. All of this packaged into a splash-proof mounting system makes it suitable for any marine application.

Features

  • 10.1″ display with modern, low profile glass design
  • Optically bonded IPS LCD provides excellent viewing angles
  • 24 bit colour for better colour accuracy and contrast
  • High resolution 1280 x 800 pixel for sharp and clear images
  • 550 nit brightness dimmable for night time viewing
  • New dual core processor provides lightning fast performance
  • Easy front mount installation and screwless rear access
  • Wide 8-32V DC voltage range
  • Consistent and familiar CZone 2.0 User Interface, customizable for any OEM
  • Wireless Server for iPad control via wired Router connection

Overview

Overview

Overview-1

Supplied Parts

Supplied Parts

  1. Touch 10 Display
  2. Metal Backing Frame
  3. Plastic mounting bracket
  4. Power Cable
  5. Torx (T7) Screwdriver
  6. Mounting Screws Short (x14)
  7. Mounting Screws Long (x14)
  8. Mounting Template

Network Configuration
The Touch 10 Gen 2 has an internal Wireless Server. When connected to a WiFi Router via the Touch 10’s ethernet port, the CZone system can be controlled wirelessly from an iPad and favorites packages can be sent to The Touch 10 wirelessly. The Client Mode configuration is detailed below:

Network Configuration

Figure 3. Client Mode Wired Example

System Example

System Example

Installation

Things You Need

  • Touch 10 Display
  • Metal Backing Frame (supplied)
  • Plastic Mounting Bracket (supplied)
  • Power Cable (supplied)
  • 14 x Mounting Screws (supplied)
  • Mounting Template (supplied)
  • NMEA2000 drop cable and T-connector
  • 3A Fuse
  • Screw driver and drill bits
  • Electrical Tools

Mounting Location
When selecting a location for the Touch 10 Display it is important to consider the following factors:

  • Ensure mounting wall thickness is 25mm or less (maximum supported by mounting bracket)
  • Ensure mounting compartment is of suitable size with adequate airflow
  • Ensure display is mounted in a location where it will not be subjected to excessive vibration
  • Ensure display is mounted in a location where the operator can easily use controls and clearly see the screen
  • Ensure display is mounted in a location that allows proper routing, support and connection of cables
  • Ensure cables have adequate strain relief to prevent stress on connectors
  • Select a location that is far enough away from devices that may cause interference, such as motors, generators and radio transmitters/receivers.
  • The display has a high-contrast screen, and is viewable in sunlight, but for best results install the unit out of direct sunlight.

Warning! Inadequate ventilation may cause the unit to overheat. The unit is designed to operate in temperatures from 0° C to +50° C.

Mounting Instructions
Follow the below steps for mounting the Touch 10 to the chosen mounting surface

Mounting Instructions

Figure 4. Mounting Exploded View

  1. Place supplied cutout template on mounting wall using adhesive tape (note: maximum wall thickness = 25mm)
  2. Use a 10mm drill bit to cut four corner holes
  3. Cut along dotted line and remove inner section
  4. Remove the VHB tape liner from back of the plastic mounting bracket and take note of the TOP and BOTTOM labels
  5. Insert plastic mounting bracket in to mounting hole but do not stick to mounting wall yet
  6. Hold metal backing frame behind mounting wall cutout and secure to bracket using the supplied screwdriver and 14 screws (note: two screw sets are supplied. Use short screws for walls 15mm or less and long screws for walls up to 25mm)
  7. Once all screws are tightened, press bracket down firmly to ensure bracket bonds to wall with the VHB tape
  8. Insert Touch 10 into mounting bracket by hooking top of panel into bracket and pressing bottom of display until it clips firmly in to place
  9. To remove Touch 10 from bracket, carefully insert flathead screwdriver into slot at bottom of display and twist until it unclips
Connections

Warning: Before starting the installation, be sure to turn electrical power off. If power is left on or turned on during the installation, fire, electrical shock, or other serious injury may occur. Be sure that the voltage of the power supply is compatible with the unit.

Connections

Figure 5. Connections

  1. Connect Ethernet to Router (Optional)
    Run an ethernet cable from the Ethernet port on the Touch 10 to an ethernet port on the router, only if the Touch 10 will be configured in Ethernet Mode for iPad connectivity.

  2. Connect NMEA 2000 Network
    Run NMEA2000 Drop cable from NMEA2000 port on Touch 10 to NMEA2000 backbone.

  3. Connect DC Power Cable
    The unit has a voltage rating 8 to 32V DC, hence it can be installed in either 12V or 24V systems.

  4. Connect Red wire on DC Power Cable to Battery Positive (+) ensuring a 3 Amp fuse is installed inline.

  5. Connect Black wire on DC Power Cable to Battery Negative (-).

  6. Plug the supplied power cable to the DC Power port on the Touch 10.

Operation

First Power Up
If connecting Touch 10 to an existing CZone network, ensure the display has been added to the CZone configuration and assigned a dipswitch. Every CZone device on a network requires a unique dipswitch to operate correctly, and the Touch 10 has a virtual dipswitch. Refer to the CZone Configuration Tool manual for this process.

  1. Turn on the circuit breaker or switch supplying power to the Touch 10.
  2. The CZone splash screen will appear for about 1 minute then the display will attempt to claim a configuration from the network.
  3. When configuration has been successfully claimed you will be prompted to enter the display dipswitch. Select the dipswitch from the list of configured devices or set the dipswitch manually by checking the correct boxes.
  4. After dipswitch has been entered successfully the Control or Modes page (if configured) will.
  5. The Touch 10 is now ready for use.
    Note: Refer to CZone 2.0 User Interface Manual for detailed operation instructions.

Operation

Operation-1

Updating Software
To keep the Touch 10 up to date with the latest software refer to https://downloads.czone.net/. It is recommended to update the entire CZone system when updating the Touch 10 to ensure the system operates correctly. The Touch 10 can be updated via the USB port, see process below:

Checking Current Software Version

Operation-2

To check the current software version on the Touch 10, go to Settings > About.
The current software version is listed at the top of the page. To install a newer version, follow the below steps

Updating Software via USB Flash Drive

  1. Copy the Touch 10 Gen 2 firmware file (extension .swu, previously downloaded from the CZone portal) on the root directory of a USB Flash Drive.
  2. Insert the USB Flash Drive in the USB Port of the Touch 10.
  3. Press the ‘Update Software’ button on the Settings > About page and press ‘Yes’ when prompted.
  4. The display will start installing the new software, this process may take a few minutes.
  5. When complete the display will boot up to the main screen. Go to Settings > About to confirm the new Software Version.

Specifications

Technical Specifications

Model CZone Touch 10 Generation 2
Article number 80-911-0216-00
Type LCD IPS TFT (Optically Bonded)
Touch Screen Projected Capacitive Multi-Touch
Glass 1.1mm
Brightness 550cd/m2
Resolution 1280 x 800 pixels, WXGA
Aspect Ratio Widescreen (16:10)
Backlight LED
Colour 24-bit RGB
CPU iMX6, Dual Core
Memory SDRAM 1GB, 8GB e.MMC
Peripherals Battery-backed real time clock
Power Supply 8-32VDC
Power Consumption 1A @ 12V, 500mA @ 24V
Ingress Protection IP66
Operating Temperature 0 to 50 degC
Storage Temperature -30 to 80 degC
Interfaces NMEA 2000, USB 2.0, 10/100Mbps Ethernet, GPIO
Weight 1.9kg (4lb 3oz)
Dimensions (H x W x D) 279mm x 200mm x 41mm (10⅞” x 7¾” x 1⅝”)
Certification CE, NMEA

Dimensions

Dimensions

Ordering Information

Touch 10 Generation 2 Part Numbers and Accessories

Part Number Description
80-911-0216-00 CZONE TOUCH 10 GENERATION 2 KIT
80-911-0032-00 CZONE TOUCH 10 POWER CABLE 2m (6.5ft) (SPARE)
80-911-0114-00 CZONE TOUCH 10 MOUNTING BRACKET KIT (SPARE)

EC DELCARATION OF CONFORMITY

CONFORMITY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals