lowes A05069 Labradorite 22 2 in 3 Light Polished Gold Instruction Manual

June 15, 2024
lowes

lowes A05069 Labradorite 22 2 in 3 Light Polished Gold

Product Information

Item Number: A05069

Specifications:

  • Installation : by a licensed electrician is recommended
  • Voltage: 120V
  • Maximum wattage per bulb: Type B, Max 40W
  • The mounting : surface should be clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides

Product Usage Instructions

Safety Precautions

To reduce the risk of fire, electric shock, or personal injury, please follow these safety precautions:

  1. Read the instruction manual carefully and save it for future reference.
  2. Before starting any work, always shut off the electricity.
  3. Ensure the mounting surface is clean, dry, flat, and strong enough to support the lamp.
  4. Make sure the ceiling or wall can withstand the weight of the lamp before installation.
  5. Avoid exposing the lamp to acidic and alkaline substances.
  6. When replacing bulbs, turn off or unplug the lamp and wait until it is cool.
  7. Use common sense, caution, and care when dealing with electrical products.

Tools Required

Before starting assembly and installation, make sure you have the following tools:

  • Ladder
  • Philips Head or Flat Blade Screwdriver
  • Electrical Tape
  • Pliers
  • Wire Cutter/Stripper

Assembly & Installation Instructions

  1. Carefully remove the fixture from the carton and ensure all parts and accessories are included.
  2. Turn off the power before starting the installation.
  3. Secure the mounting plate (D) to the outlet box using the provided mounting screws (A).
  4. Connect the wires according to the wire connection chart.
  5. Ensure that the ground wire is connected to the green ground screw.

FAQ

Q: What is the maximum wattage for each bulb?

A: The maximum wattage per bulb is Type B, Max 40W.

Q: Can I install the lamp myself?

A: While self-installation is possible, we recommend installation by a licensed electrician for safety reasons.

Q: What should I do if there are gaps between the mounting surface and canopy?

A: Any gaps exceeding 3/16 should be corrected to ensure proper installation. The mounting surface should be clean, dry, flat, and strong enough to support the lamp.

Q: Can I replace bulbs while the lamp is still on?

A: No, always turn off or unplug the lamp and wait until it is cool before replacing bulbs.

WARNING

(To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2.  Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
  4.  Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
  5. Place the wall switch in the “OFF” position.
  6. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  7. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  8. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
  9. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  10. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  11. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

lowes-A05069-Labradorite-22-2-in-3-Light-Polished-Gold-
fig1

PARTS AND TOOLS

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

lowes-A05069-Labradorite-22-2-in-3-Light-Polished-Gold-
fig2

PARTS INCLUDING:

lowes-A05069-Labradorite-22-2-in-3-Light-Polished-Gold-
fig7

  • (C) Green ground screw (1)
  • (D) Mounting plate (1)
  • (E) Backplate (1)
  • (F) Knob nut (2)
  • (G) Cover (3)
  • (H) Crystal Hook (48)
  • (I) Crystal (48)
    • ACCESSORIES ENCLOSED:
  • (A) Mounting screw (2)
  • (B) Plastic wire connector (3)
  • (H) Crystal hook (3) (spare part)
  • (I) Crystal (1) (spare part)

INSTALLATION INSTRUCTIONS

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

  • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
  • Place the wall switch in the “OFF” position.

Make assembly

lowes-A05069-Labradorite-22-2-in-3-Light-Polished-Gold-
fig3

Step A1 : Unscrew knob nuts (F) from the back plate (E), then set them aside for later installation.
Step A2: Carefully pass the supply wires from the outlet box through the mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3: Make wire connections
Connect wires as below wires connection shown.

PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the chart below

Connect wires according to the chart below

  • Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in the back plate (E) with the pre-assembled mounting screws, then attach the back plate (E) to the mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE : back plate (E) should be snug against the wall with knob nuts (F). If not, remove the back plate (E), and adjust the threaded length of pre- assembled mounting screws on the mounting plate (D):

  • Unscrew the pre-assembled hex nuts.
  • Screw the pre-assembled mounting screws in or out of mounting plate (D).
  • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.

Step A5:

  1. Hang crystal hooks (H) into holes of cover (G) to hang up crystals (I) as shown in the illustration.
  2. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.

Check everything is installed properly, then you can turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

lowes User Manuals

Related Manuals