SOLIGHT WO20-W Backlit LED Light Panel Instruction Manual

SOLIGHT WO20-W Backlit LED Light Panel

Product Information

Specifications

• Model: EN WO20-W / WO24-W
• Type: Backlit LED light panel

Safety Notice

Before installing or using the product, please read and follow these safety guidelines:

1. Switch off the power supply before installation.
2. Open the terminal cover.
3. Connect the power cord and ensure it is connected correctly.
4. Attach the terminal cover.
5. Connect the power supply to the power cord.
6. Insert the power supply into the ceiling.
7. Insert the luminaire into the ceiling.
8. Switch on the power supply.

Product Usage:

To use the backlit LED light panel, please follow these steps:

Step 1: Installation

1. Switch off the power supply before starting the installation process.
2. Locate the terminal cover and open it.
3. Take the power cord and connect it to the appropriate terminals, ensuring correct polarity:
   • Brown (V+) – (L) phase
   • Blue (V-) – (N) neutral
4. Attach the terminal cover securely.
5. Connect the power supply to the power cord.
6. Insert the power supply into the ceiling, following any specific instructions provided for your ceiling type.
7. Insert the luminaire into the ceiling, aligning it properly.
8. Switch on the power supply to activate the backlit LED light panel.

Step 2: Usage

Once the backlit LED light panel is installed and powered on, you can use it as follows:

• Switch the light panel on or off using the power switch or control mechanism provided.
• Adjust the brightness level if applicable, according to the provided controls.
• Enjoy the evenly distributed and energy-efficient lighting provided by the panel.

FAQ:

• Q: Can the light source be replaced?
• A: No, the light source of this luminaire is non-replaceable. At the end of its service life, the entire luminaire must be replaced and disposed of in a designated place.
• Q: Is the product compliant with regulations in the EU?
• A: Yes, Solight Holding s.r.o. declares that the product complies with the requirements and provisions of Directive 2014/53/EU. The equipment can be freely operated in the EU. The Declaration of Conformity can be found at www.solight.cz. The product can be operated under general authorization No.VO-R/10/05.2014-3.
• Q: Why is the entire product considered a light source?
• A: The light source of this product cannot be removed for verification due to design reasons. Therefore, the entire product is considered a light source.

Dear customer, thank you for purchasing our product. Please read the following instructions carefully and follow them to serve you safely and to your full satisfaction. This will prevent misuse or damage. Avoid unprofessional handling of this appliance and always observe the electrical appliance usage guidelines. Keep the instruction manual carefully. For use in the home or indoors. This product should only be used by an adult. Never expose to environments with high humidity (e.g. bathroom), and avoid contact of the product with liquids. Installation may only be carried out by a qualified worker qualified according to Decree No. 50/1978 Coll. as amended, at least a worker knowledgeable according to § 5 of Decree No. 50/1978 Coll. as amended.

SAFETY NOTICE

• Installation must only be carried out by a qualified electrician.
• Power supply: 220-240V AC 50/60 Hz.
• Use only indoors.
• If the power cord of this luminaire is damaged, it must be replaced by the manufacturer’s service department.
• There are no replaceable parts in the device.

INSTALLATION

1. Switch off the power supply before installation.
2. Open the terminal cover.
3. Connect the power cord and make sure it is connected correctly.
4. Attach the terminal cover.
5. Connect the power supply to the power cord.
6. Insert the power supply into the ceiling.
7.  Insert the luminaire into the ceiling.
8. Switch on the power supply.

Solight Holding s.r.o., declares that the product complies with the requirements and provisions of Directive 2014/53/EU. The equipment can be freely operated in the EU. The Declaration of Conformity can be found at www.solight.cz. The product can be operated under general authorization No.VO-R/10/05.2014-3 The light source of this luminaire is non-replaceable, at the end of its service life the entire luminaire must be replaced and disposed of in a designated place. This product contains a light source that for design reasons cannot be removed for verification and therefore the entire product is considered a light source.

References

• SOLIGHT.cz | Váš B2B partner a velkoobchod pro Osvětlení, Elektro, Smart Home, Měřící techniku a dalších 1500+ produktů

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>