PELONIS PFS40A4BBB 16 Inch Stand Fan Owner’s Manual

June 15, 2024
Pelonis

PELONIS PFS40A4BBB 16 Inch Stand Fan

Product Information

  • Model: PFS40A4BBB, PFS40A4BWW
  • Product Name: Stand Fan
  • Specifications
    • Polarized plug
    • Overload protection (fuse)
    • Remote control with a 5m effective range
    • Horizontal swing feature
    • Tilt adjustment
    • Height adjustment

Product Usage Instructions

Installation Instructions
Name of components

  • Motor shaft
  • Base
  • Right-angle bolt
  • Rear grill
  • Pole
  • Front grill
  • Lock nut of blade
  • Blade
  • Lock nut of grill

Base Installation

  1. Align the column with the groove on the base.
  2. Fix them together using a right-angle bolt.
  3. Tighten the knob to secure the base.

Front and Rear Guard Installation

  1. Align the screw holes on the outer ring of both the Front and Rear Guards with the Positioning Clip.
  2. Press down all the buckles to fasten the Front Guard with the Rear Guard.
  3. Tighten the separated screw and nut at the screw holes.

Motor Installation

  1. Install the motor by aligning it with the pole.
  2. Tighten the lock nut of the blade anticlockwise.
  3. Install the front fan cover.
  4. Pull the blade to rotate after installation to ensure normal rotation.
  5. Screw the lock nut of the grill clockwise and fix the rear grill.

Instructions for Use
Remote Controller

  • SPEED key: Adjust the fan speed.
  • ON/OFF key: Turn the fan on or off.
  • TIMER key: Set a timer for the fan.

Note: The effective range of the remote control is within a 5m distance and 30-degree deflection in front of the product.

Body

  • Speed display: Indicates the current fan speed.
  • Timer display: Displays the set timer duration.

Operation of Body

  • Horizontal Swing: Pull up to keep the fan static, and push down to enable swing mode.
  • Tilt Adjustment: Adjust the tilt angle manually.
  • Height Adjustment: Turn counterclockwise to loosen for performing height adjustment.

User Servicing Instructions

  1. Grasp the plug and remove it from the receptacle or outlet device. Do not unplug by pulling on the cord.
  2. Open the fuse cover by sliding it towards the blades.
  3. Remove the fuse carefully. Insert the tip of your tool into the fuse slot (close to the terminal) and gradually prize the fuse out. If it feels tight, try multiple times and prize the fuse little by little. Once one side of the fuse has been prized, remove the fuse entirely.

FAQ (Frequently Asked Questions)

  • Q: How do I clean the fan?
    A: Disconnect the fan from the power source and remove the grilles. Clean the grilles, blade, and other parts with a soft cloth or brush. Avoid using water directly on the motor or electrical components.

  • Q: Can I use the fan in a window?
    A: No, using the fan in a window is not recommended as it may create an electrical hazard due to rain.

  • Q: What should I do if the fan doesn’t fit fully in the outlet?
    A: If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

SAFETY INSTRUCTION

CAUTION Read Rules for Safe Operation and Instructions Carefully.
WARNING This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safely feature.
WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.

RULES FOR SAFE OPERATION

  1. Never insert fingers, pencils, or any other object through the grille when fan is running.
  2. Disconnect fan when moving from one location to another.
  3. Disconnect fan when removing grilles for cleaning.
  4. Be sure fan is on a stable surface when operating to avoid overturning.
  5. Do not use fan in window. Rain may create electrical hazard.
  6. Ensure that the fan is switched off from the supply mains before removing the grille.

The rules about cord and plug as below:

  1. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the products. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.
  2. Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
  3. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will be tripped over.

INSTALLATION INSTRUCTIONS

Name of components

Base Installation
Align the column with the groove on the base and fix them together using a right-angle bolt.

Considerate Hint: Remove ① ② parts from the component before performing installation.

Front and Rear Guard Installation

  1. Align Screw Holes on the outer ring of both the Front and Rear Guards, with the Positioning Clip aligned as illustrated.
  2. Press down all the Buckles to fasten the Front Guard with the Rear Guard. At the Screw Holes, tighten the separated screw and nut.

INSTRUCTIONS FOR USE

Instructions for key of remote controller

Considerate Hint:
Effective Range of Remote Control: within 5 m distance and 30-degree deflection in front of Product

Instructions for display of body

Instructions for operation of body

USER SERVICING INSTRUCTIONS

  • a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
  • b) Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.
  • c) Remove fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal), then prize the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at several times and prize the fuse little by little. When one side of the fuse has been prized, then you can get the fuse out entirely.
  • d) Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
  • e) Close fuse cover. Slide closed the fuse access cover on top of the attachment plug.
  • f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.

Notice:

  1. When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damage or cause accident.
  2. When you feel it hard to operate, please make sure you have got the right way.

CLEANING

  1. Be sure to unplug from the electrical supply source before cleaning.
  2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly to remove soap film with clean water.
  3. Be sure not to make water or other liquid enter inside of motor.

SERVICE & SUPPORT
In the event of a warranty claim or if service is required for this heater, please contact us at the following:
Tel: 1-866-646-4332
Email us at: customersupport@pelonis.com
For questions or comments, please write to:
Midea America Corporation
5 Sylvan Way, Parisippany, NJ 07054
For your records, staple your sales receipt to this manual and record the following:

  • DATE OF PURCHASE: ___
  • PLACE OF PURCHASE: __

(STAPLE SALES RECEIPT HERE)

NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals