EDIFIER EDF200142 X5 Lite True Wireless Earbuds User Manual
- June 15, 2024
- Edifier
Table of Contents
X5 Lite
True Wireless In-Ear Headphones
Manual
EDF200142 X5 Lite True Wireless Earbuds
For more information, please visit our website:
| |
---|---|---
@Edifierglobal| @Edifier_Global| @Edifier_Global
Model: EDF200142
Edifier International Limited P.O. Box 6264 General Post Office Hong Kong
www.edifier.com
2023 Edifier International Limited. All rights reserved.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade, information
contained herein may be subject to change from time to time without prior
notice.
Products of EDIFIER will be customized for different applications.
Pictures and illustrations shown on this manual may be slightly different from
actual product.
If any difference is found, the actual product prevails.
IB-200-X5LITE-00 V1.0
Power ON/OFF
- Power ON when taken out of the case.
- Power OFF when placed in the case.
Note:
If there is no Bluetooth connection for 10 minutes after powered on, the
earbuds will power off automatically.
Pairing
1st Pairing
- Taken out of the case. White and red LEDs will blink alternately.
- Select “EDIFIER X5 Lite” in Bluetooth device setting to connect.
White LED will blink twice in 5 seconds when successfully.
Note：
For subsequent use, the earbuds will automatically connect to the device used
last time.
Reset
-
Taken out of the case.
-
Disconnected from any Bluetooth device.
Press and hold the touch panel on either earbud for around 8s until red LED blinks 6 times to clear the Bluetooth pairing records and power off. If the left and right earbuds are connected, the other side will clear the Bluetooth pairing record and power off too. -
Placed back in the case and taken out of the case again.
-
Select “EDIFIER X5 Lite” in Bluetooth device setting to connect.
White LED will blink twice in 5 seconds when successfully.
Left & Right connection
-
If there is no Bluetooth connnection and TWS connection when earbuds ar powered on, respectively tap the touch panel 5 times on both earbuds until white LED blinks slowly to enter TWS pairing mode. Once the left and right earbuds are connected
successfully, white and red LEDs will blink alternately to enter Bluetooth pairing mode. -
Select “EDIFIER X5 Lite” in Bluetooth device setting to connect.
White LED will blink twice in 5 seconds when successfully.
Charging
Earbuds
- When hearing a low battery prompt tone, please place the earbuds in the case for charging.
- Red LED on earbud is steady lit when charging and off when fully charged.
Charging Case
- Please connect the case to power source with the included Type-C charging cable for charging.
- Red LED is steady lit when charging and off when fully charged.
Note:
Please do not charge the earbuds when there is sweat or other liquids inside
the charging port, which may damage the earbuds.
Input: 5V 200mA (Earbuds)
5V 1A (Charging case)
Controls
Note:
- Images are for illustrative purposes only and may differ from the actual product.
- Download Edifier Connect App for more customizable control settings.
http://www.edifier.com/cn/zh/app/download/5b5eafdd7da08b00295bd49d
FCC statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
IC statement:CAN ICES-003(B) / NMB-003(B).
FCC ID: Z9G-EDF209
IC: 10004A-EDF209
201-230498
Input: 5V 200mA(Earbuds)
5V 1A(Charging case)
Hereby, Edifier International Limited declares that the radio equipment type
EDF200142 is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet
address:https://www.edifier.com/int/eu-doc.html
Declaration for EU
Frequency Band: 2400MHz – 2483.5MHz
RF Power Output: ≤13 dBm (EIRP)
There is no restriction of use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>