TRINITY THA-0307 Basics Stainless Steel Utility Sink Owner’s Manual

: June 15, 2024
: TRINITY

Table of Contents

TRINITY THA-0307 Basics Stainless Steel Utility Sink
PARTS LIST
ASSEMBLY INSTRUCTIONS
SERVICE PARTS LIST
CARE AND MAINTENANCE
PRODUCT REGISTRATION
WARRANTY
CONTACT US
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TRINITY THA-0307 Basics Stainless Steel Utility Sink

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
PRODUCT

Important

FOR 3D ASSEMBLY INSTRUCTIONS
Intelligent Instructions

PARTS LIST

Your TRINITY Basics Stainless Steel Utility Sink w/Faucet should include the following parts. Please inspect the box contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY Customer Service: at 800.985.5506 or customerservice@trinityii.com. Parts can also be requested online via our “Contact Us” section at www.trinityii.com.
A Phillips head screwdriver is required for assembly, and a pipe wrench is recommended.

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
FIG-2

ASSEMBLY INSTRUCTIONS

STEP 1

Lay SINK (A) upside-down. Unscrew HEX SCREWS (E) that are pre-installed on Leg Collars on the bottom of SINK (A) until LEGS (B) can be fully inserted.
Insert LEGS (B) into Leg Collars. Tighten both HEX SCREWS (E) on each Leg Collar with HEX KEY (G). Place a SCREW CAP (F) over each HEX SCREW (E).

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
FIG-4

STEP 2

Carefully turn the sink right-side up, standing it upright.
Unscrew the large 3-3/8” Nut from the bottom of DRAIN ASSEMBLY (D). From inside SINK (A), insert the Drain through the White Seal and opening at the bottom.
From under SINK (A), the first slide on Black Gasket and Paper Washer then screw the large 3-3/8” Nut back on tightly. If necessary, use a pipe wrench to tighten.

Note: P-trap NOT included.

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
FIG-5

STEP 3

Unscrew each screw securing Lock Nut to the bottom of the FAUCET ASSEMBLY (C) and remove Lock Nut w/Screws, Metal Washer and Rubber Gasket.
From the top side, insert FAUCET ASSEMBLY (C) through the hole. Make sure the Metal Base is on top of SINK (A). Align the faucet handle facing towards the front of SINK (A). From under SINK (A), first slide on Rubber Gasket, then Metal Washer, and lastly, screw on Lock Nut w/Screws pointed upward.
Tighten the Lock Nut as much as you can by hand and tighten the screws with a screwdriver.

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
FIG-6

STEP 4

Carefully move the sink against the wall at your desired location. If needed, use a pencil to mark off the mounting height of BRACKET (H).
Position BRACKET (H) on the wall, marking off the fastening location on the wall through holes on BRACKET (H). Drill holes in marked locations.
Insert ANCHOR (J) completely into each drilled hole. Fasten MOUNTING SCREWS (I) through these holes into the wall or anchor tightly with a screwdriver.
Slightly lift the sink and hook the flange of the sink over BRACKET (H). Adjust Feet Levelers to ensure the sink is stable and level. Connect Hoses and Drains to the plumbing system.

Note: The bracket is to prevent sink tipping, NOT for mounting the sink to a wall. Do NOT mount the sink to a wall without legs.

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
FIG-7

SERVICE PARTS LIST

TRINITY Customer Service provides the following replacement parts:

Part Number Description

XBS-19-007-1600 Bracket
XGR-01-032-0440 Anchor
XSV-01-033-0440 Mounting Screw
XBS-18-023-1816 Sink
XBK-23-005-0815 Screw Cap
XGL-04-045-1950
XGR-98-005-3775 Feet Leveler
XSV-01-034-0808 Hex Screw
XXX-97-001-0001 Hex Key
XGL-02-003-0002 Drain Assembly
CGL-02-009-0010 Faucet Assembly

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
FIG-8

WARNINGS

Read and understand all instructions. Failure to follow all instructions may result in injury and/or damage.
The warnings, cautions, and instructions discussed in this manual cannot cover all possible conditions or situations that may occur. The user must always be aware of their environment and ensure that they use the product safely and responsibly.
Do NOT modify the product in any way. Unauthorized modification may impair the function and/or safety of the product, and may affect the life of the product. Any modifications will void the product warranty.
Check for damaged parts. Before using this product, carefully check that all parts are in good condition and that the product will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace damaged or worn parts, and never use this product with a damaged part.
Do NOT overload the product.
Total weight capacity| 300 lb
---|---
Ensure backflow prevention compliance. Equipment is to be installed with adequate backflow prevention to comply with applicable federal, state and local codes.
Do NOT let children climb on or in the Utility Sink.
Ensure to install the wall bracket. Failure to do so may result in tipping.
Do NOT mount the sink to a wall without legs. The wall bracket is to prevent tipping, NOT for mounting the sink to a wall.
Ensure plumbing connections are tightened fully. Failure to tighten may result in leakage.
Strongly recommended that professional installers perform the installation. Observe local plumbing and building codes.

CARE AND MAINTENANCE

Avoid harsh, abrasive cleaners, and other corrosive chemicals. Do not leave salt in the sink or near a saltwater environment.
Rinse the surface thoroughly with hot water after using soaps and detergents containing chlorides to prevent corrosion.
Do not use scouring pads, carbon steel brushes, or steel wool for cleaning. Iron particles left behind can lead to rust.
Avoid the use of oily rags or greasy cloths when wiping the surface. Wipe dry after use so that water does not leave water spots.
Use a quality stainless steel cleaner and follow the instructions that come with the cleaner. Wipe ALONG the grain (NOT against).

PRODUCT REGISTRATION

Thank you for purchasing a TRINITY Basics Stainless Steel Utility Sink w/Faucet. To register your product and receive streamlined customer service, please fill out the following Product Registration Form and (1) fax the form to 310.347.4134 (2) complete the Product Registration Form online at www.trinityii.com or (3) scan and email the form to customerservice@trinityii.com. Include a copy of your original receipt with your submission.

TRINITY-THA-0307-Basics-Stainless-Steel-Utility-Sink-
FIG-9

WARRANTY

1-YEAR LIMITED WARRANTY

TRINITY Basics Stainless Steel Utility Sink w/Faucet Model # THA 0307
Trinity International Industries (“Trinity”) warrants to the original consumer purchaser (“Purchaser”) of the TRINITY Basics Stainless Steel Utility Sink w/Faucet (“Product”) that each Product shall be free from defects in workmanship and materials for 1 year from the date of original purchase. Trinity’s obligation under this warranty shall be limited to repair or replacement of, or adequate compensation for the Product which shall not be greater than the amount of the purchase price of the Product, at the option of Trinity, during the warranty period. All replaced parts and Products become the property of Trinity and must be returned to Trinity. This warranty excludes normal wear and tear of the Product and its parts or components, and damage arising from any of the following: negligent use or misuse of the Product, use contrary to this User’s Manual, or alteration by anyone other than Trinity. The warranty period of 1 year shall not be extended or renewed by the repair or replacement of, or compensation for, the Product. Any warranty implied by applicable law is limited in duration to one year from the date of purchase and is subject to the same conditions and limitations as are provided for our express warranty. Except as set forth herein, and to the extent applicable there are no warranties on this Product either express or implied, and Trinity disclaims all warranties including, but not limited to, any implied warranties of merchantability, infringement or fitness for a particular purpose. No warranty or guarantee given by any person, firm, or corporation for this product shall be binding on Trinity. If your Product is defective or otherwise requires service or parts, please call TRINITY Customer Service toll-free at (800) 985 5506, between 5:00 a.m. and 5:00 p.m., PST. Please tell us which model you purchased, the date of the purchase, and the problem with your Product. A copy of your original purchase receipt must accompany your service request.

LIMITATION OF REMEDIES AND LIABILITY

Trinity (and its employees, officers, members, managers, affiliates and assigns) shall not be liable for any incidental, consequential, special, indirect, remote, special or punitive damages for breach of any warranty, express or implied, including, but not limited to, lost profits, lost savings, loss of anticipated benefits and attorneys’ fees, which arise out of the purchase, use or inability to use the Product, whether arising out of contract, negligence, strict tort, product liability, or any other legal theory on which a claim is based. As noted above, to the extent damages are allowed by our express warranty or by applicable law, those damages may not exceed the purchase price paid for the Product. Without limiting the foregoing Purchaser assumes all risk and liability for loss, damage or injury to Purchaser and Purchaser’s property and to others and their property arising out of the use, misuse, or inability to use this Product. This limited warranty shall not extend to anyone other than the original purchaser of this product, is nontransferable and states your exclusive remedy. Some states do not allow the exclusion or limitation of incidental, consequential, special, or punitive damages, so the above limitation or exclusion may not apply to you. The above warranty gives you specific legal rights, and you may have other rights that vary from state to state.