lowes A05161 Oudspeaker 8-Light Polished Gold with Spider Glass Modern LED Dry Rated Chandelier Instruction Manual
- June 15, 2024
- lowes
Table of Contents
lowes A05161 Oudspeaker 8-Light Polished Gold with Spider Glass Modern
LED Dry Rated Chandelier
Product Information
Specifications
- Item Number: A05161
- Maximum Wattage : Type B, Max 40W per bulb
- Voltage: 120V
FAQ
- How do I order replacement parts?
- Keep the provided sheet for future reference and order replacement parts from the place of purchase. Use the exact wording from the illustration when ordering.
Product Usage Instructions
Warning
To reduce the risk of fire, electric shock, or personal injury, please follow these precautions:
- We suggest installation by a licensed electrician.
- Read the instruction carefully and save it for future reference.
- Before starting any work, always shut off the electricity.
Mounting Surface Preparation
Before installation, ensure the mounting surface meets the following requirements:
- Clean, dry, flat, and strong enough
- 1/4 larger than the canopy on all sides
- Correct any gaps between the mounting surface and canopy exceeding 3/16 as required.
Ceiling/Wall Weight Capacity Check
- Ensure that the ceiling or wall can withstand the weight of the lamp before installation.
Lamp Maintenance and Safety
- Keep the lamp away from acidic and alkaline substances to prevent damage to the surface.
- When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs can get hot quickly.
- Use common sense, caution, and care with any electrical products.
Cleaning
To clean the fixture:
- Wipe with a soft cloth.
- Clean glass with a mild cleaner, such as mild and non-abrasive soap.
- Avoid using abrasive materials like scouring pads, powders, steel wool, or abrasive paper.
Tools Required
Before starting assembly and installation, make sure you have the following tools (NOT INCLUDED):
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
SAFETY INSTRUCTION
WARNING
(To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per blub.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
TOOLS
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
PARTS
PARTS TYPE & QTY INCLUDING:
(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Collar ring (1)
(G) Collar loop (1)
(H) Quick link (2)
(I) Chain (1)
(J) Loop (1)
(K) Arms assembly (1)
(L) Upper arm (4)
(M) Lampshade (8)
(N) Socket (8)
(O) Lower arm (4)
ACCESSORIES & QTY ENCLOSED:
- (A) Wire connector (3)
- (B) Mounting screw (2)
- (C) Single bar (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Collar ring (1)
- (G) Collar loop (1)
- (H) Quick link (2)
- (I) Chain (1)
- (J) Loop (1)
- (K) Arms assembly (1)
- (L) Upper arm (4)
- (M) Lampshade (8)
- (N) Socket (8)
- (O) Lower arm (4)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
- Step A1 : Adjust arms ( L & O ) to the proper position as shown in the illustration.
- Step A2: Screw loop (J) onto top of arms assembly (K).
- Step B1: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
- Step B2: Attach quick links (H) to chain (I) and loop (J) on the top of arms assembly (K).
- Step B3 :Carefully weave the fixture wires through main chain (I) in and out of every other link and stop just when you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed.
Turn off power
Before you start the installation, NEVER attempt any work without shutting off
the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
Make installation
- Step C1 : Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B)
- NOTE: the side of the single bar (C) marked “GND” must face out.
- Step C2: Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position. Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to the following note, you will know the proper position where the collar loop (G) should be located.
- NOTE: canopy (E) should be snug against the ceiling and collar loop (G) should be screwed with enough threads (no less than 6 threads) on the pre-assembled threaded nipple for more secure hanging.
- If not, adjust the collar loop (G) on the single bar (C) by screwing the collar loop (G) in or out of the single bar (C) until the secure length is achieved.
- Step C3: Pass chain (I) through collar ring (F) and then through canopy (E).
- Step C4: Open quick link (H), and attach quick link (H) to collar loop (G). Close quick link (H).
- Pass the fixture wires through the collar loop (G) to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed.
- Step C5 : If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above the single bar (C) is at least 6″.
- Step C6: Make wire connections
- Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Twist wires together with plastic wire connectors (A) until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step C7: Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).
- Step C8: 1 Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Screw lampshades (M) onto sockets (N) as shown in the illustration.
Check everything is already installed properly, and then you can turn on the light. Enjoy!
CONTACT
- +1850 296 2377
- Working hours: Mon – Fri 9:00 – 16:00
- EST : homecustomercare@outlook.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>