lowes A0517704 6 Light Matte Black and Polished Gold Modern LED Dry Rated Chandelier Instruction Manual
- June 15, 2024
- lowes
Table of Contents
Lowes A0517704 6 Light Matte Black and Polished Gold Modern LED Dry Rated
Chandelier
Product Information
Item Number: A0517704
Specifications:
- Installation by a licensed electrician is recommended
- Voltage: 120V
- Maximum wattage: Type B, Max 40W per bulb
- The mounting surface should be clean, dry, flat, and strong enough
- The mounting surface should be 1/4 larger than the canopy on all sides
- The ceiling or wall should be able to support the weight of the lamp
- Avoid contact with acidic and alkaline substances
- Turn off or unplug the lamp before replacing the bulbs
Product Usage Instructions
Preparation
Before starting assembly and installation, please prepare the following
tools (NOT INCLUDED):
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Assembly and Installation
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Screw tubes (I) to the top of socket assembly (J).
- Close quick links (H).
- Turn off the power before starting the installation.
- Ensure the side of the mounting plate (C) marked GND faces out.
- Connect wires according to the provided wire connection chart.
- Securely attach the assembled screws to the mounting plate (C).
FAQ
- Q: Can I install the product myself?
- A: While installation by a licensed electrician is recommended,you can install the product yourself following the provided instructions.
- Q: What is the maximum wattage for each bulb?
- A: The maximum wattage is Type B, Max 40W per bulb.
- Q: Can I use this product with a voltage other than 120V?
- A: No, the product is designed for use with a voltage of 120V only.
- Q: How should I clean the lampshade?
- A: Use a soft, dry cloth to clean the lampshade. Avoid using acidic or alkaline substances as they may damage the surface of the lamp.
Item Number: A0517704
WARNING: (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools
as below picture
PARTS TYPE & QTY INCLUDING:
- (C) Mounting plate(1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Loop (2)
- (G) Ball nut (2)
- (H) Quick link (2)
- (I) Tube
- (J) Socket assembly (1)
- (K) Socket arm (5)
- (L) Socket (5)
- (M) Lampshade (5)
ACCESSORIES & QTY ENCLOSED:
- (A) Wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
Step A1 »
- Carefully pass the fixture wires through tubes (I) and loops (F).
- Screw tubes (I) to top of socket assembly (J).
Step A2 »
- Open quick links (H).
- Attach quick links (H) to loops (F) on canopy (E) and on the top of tubes (I).
- Close quick links (H).
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Make installation
Step B1 »
- Unscrew ball nuts (G) from mounting plate (C).
Step B2 »
- Attach mounting plate (C) to the outlet box with mounting screws (B).
Note : the side of the mounting plate (C) marked “GND” must face out.
Step B3 »
Make wire connections
Connect wires as below wires connection shown below.
PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
-
Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape and sure that no wire strands are exposed.
- Carefully tuck all wires into the outlet box.
Step B4 »
Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening ball nuts (G) onto pre-assembled screws on mounting plate (C).
NOTE : canopy (E) should be snug against the ceiling with ball nuts (G). If not, remove canopy (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C):
- First, unscrew the pre-assembled hex nuts.
- Then, screw the pre-assembled mounting screws in or out of the mounting plate (C).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step B4.
Step B5 »
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Carefully screw lampshades (M) onto sockets (L) as shown in the illustration.
Check everything is already installed properly, and then you can turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustrations when ordering parts.
CLEANING
- To clean, wipe the fixture with a soft cloth.
- Clean glass with a mild cleaner (such as mild and non-abrasive soap).
- Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>