HICFM FAN-P20TM Misting Pedestal Fan Instruction Manual
- June 15, 2024
- HICFM
Table of Contents
HICFM FAN-P20TM Misting Pedestal Fan Instruction Manual
READ AND SAVE THESE INSTRUCTIONS
- To prevent serious injury or property damage, read and understand owner’s manual before operating.
- This product can be used indoor or outdoor with a proper GFCI plug.
SAFETY INFORMATION
WARNING
- Read and save these instructions. Do not operate fan unless you have read these instructions.
- Unplug the fan before moving it or performing maintenance. Do not touch the fan when your hands are wet.
- Those who are not qualified electricians should not disassemble, repair or rebuild the fan.
- Unplug the fan when it is not in use.
- DO NOT unplug the fan by pulling the cable cord. Unplug by holding the plug and pulling.
- DO NOT use the fan when there is damage to the cable cord or plug. If the supply cord is damaged, it has to be replaced by the manufacturer, its service agent or similarly qualified persons.
- To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Do Not Use Replacement Parts That Have Not Been Recommended By The Manufacturer (e.g. Parts Made At Home Using A 3D Printer).
- DO NOT use the fan close to fires.
- DO NOT insert your hand or other objects into the grille or the movable parts.
- To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
- Do Not Use An Extension Cord With This Fan.
CAUTION
- Unplug the fan from the socket and clean it with a soft cloth.
- DO NOT immerse the fan.
- Fit the guard onto fan before starting up the fan.
- This fan is not intended for use by people (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervisionor or instruction concerning use of the fan by a person responsible for their safety. Supervise children to ensure they do not play with the fan.
PACKAGE CONTENTS
ASSEMBLY INSTRUCTION
Step 1
Attach the outer tube to the base with the 4 screws as shown.
caution: The screws must be fully tightened before the fan operating.
Step 2
Assembly the fan head with the standing pipe.
Step 3
Insert the fan head into the upper tube and lighten by screws.
Caution: the screws must be fully lightened before the fan operating.
Step 4
Connect the misting switch (1) to the water pipe (2) and tighten it. Turn the switch (open) to open the misting function. Turn the switch (close) to close the misting function.
OPERATION INSTRUCTION
1) Adjusting the fan tilt angle
- Ensure the fan is unplugged from the power source beforeadjusting the height or angle.
- Place the fan on a safe, flat surface where it cannot fall or be pulled by the cord.
- Tilting the fan head upward or downward for your desired direction of air flow, and securing it by knobs of two side.
- Turning the fan On/Off and adjusting the airflow settings
- plug the fan into an electrical outlet.
- Adjust the desired speed by pulling the chain switch at the motor.
0 Stop 1 Low 2 Medium 3 High
Always turn off and unplug the fan after using.
Test GFCI (Ground Fault Circuit Interrupter) plug BEFORE EACH USE.
Plug GFCI into power outlet. Press RESET button. Indicator should turn red.
Press TEST button. Indicator should turn off. GFCI plug is tripped.
Press RESET button again for use. DO NOT USE FAN IF ABOVE TEST FAILS.
Call customer service for assistance.
CARE AND MAINTENANCE
Unplug the appliance before cleaning. Don’t use any water for cleaning metal surfaces. Slightly moisten a cloth and then wipe off the surfaces of the fan. In order to remove dust from the grill, use a vacuum cleaner or remove the front grill by removing the securing screws on the edge of the grill. After cleaning, remount the grill. After doing this, fasten the screws on the edge of the grill.
1-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from manufacturing defects
in the material and workmanship under normal use for a period of one year
after the date of purchase by the original purchaser.
This warranty does not cover transit damages. This warranty does not apply to
damages from accident, misuse, alteration of any kind to the fan or where the
connected voltage is more than above the nameplate voltage. This warranty does
not apply to the finish on any portion of the product. Servicing performed by
unauthorized persons shall render the warranty invalid. The warranty is not
responsible for damages of any kind, including accident and consequential
damages. Some states do not allow the exclusion or limitation of the
incidental or consequential damages, so the above exclusion or limitation may
not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
REPLACEMENT PARTS LIST
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>