Waterdrop WD-G3-W RO Reverse Osmosis Water Filtration System User Manual
- June 15, 2024
- Waterdrop
Table of Contents
Waterdrop WD-G3-W RO Reverse Osmosis Water Filtration System
Parts List
Inspect the package as parts list first.
Identify and get familiar with all components for quick installation.
- System Housing **X1 Set
**
- WD-G3-CB **X1
**
- WD-G3-CF **X1
**
-
WD-G3P600-RO X1
-
Red 1/4″PETubing **X60″
**
- Lock Clip **X5
**
- Teflon Tape **X1
**
- Power Adapter **X 1 Set
**
Preinstalled
-
* Smart Digital RO Faucet **x1
**
* White 1/4″ PE Tubing **X60″ **
* Feed Water Adapter 3/8″ **-1 /2″ X 1 Set **
* White 3/8 “ **PETubingX 60″ **
* Drain Saddle 1/4″ **X 1 Set **
Sample Connection
-
A. Filter Life Indicators
-
B. Display Screen: TDS Reading, Flushing Status,
Malfunction Code -
C. Activated Carbon Filter (CB)
-
D. Pre-sediment and Carbon Block Filter (CF)
-
E. Reverse Osmosis Membrane Filter (RO)
-
F. “POWEW Port
-
G. “FAUCET” Connector
-
H. “INPUT” Water Port
-
I. “FILTERED” Water Port
-
J. ‘WASTE” Water Port
-
K. Feed Water Adapter
-
L. Preinstalled Filtered Water
Tubing With Faucet -
M. Drain Saddle
-
N. Power Socket
-
O. Faucet Power Cord
-
P. Water Reservoir
(Front)
Quick Installation
Before installation, please note:
- The RO system must be connected to the COLD water supply only.
- Do not install the system in exposure to direct sunlight or harmful chemicals, nor any place where it may be damaged.
Step 1:
Install the Feed Water Adapter (K)
- Turnoff cold water supply valve.
- Connect the feed water adapter to your cold water supply pipe.
Step 2:
Install the RO Faucet (Non-Air Gap Faucet)
- If your kitchen sink or countertop does not have an existing hole. you will have to drill one (1″) referring to the Instruction Manual.
- Insert the faucet head into faucet body.
- Insert faucet stem and power cord into the hole on countertop
- Under the sink, slip on other parts in the order as shown in the picture.
Step 3:
Install the Drain Saddle (M)
- Choose a spot on the vertical drain pipe as high as possible and drill a 1/4B hole.
- Use the”WASTE”water tubing as a guide to position the drain saddle by tightening screws and nuts evenly.
Step 4:
Posiitlon the RO System Housing
- An ample flat area is required to place the system housing.
- Position the front panel facing towards you for future indicator checking.
Step 5:
Connect the Tubings
NOTE Malke sure each tubing is inserted firmly and fully untill you reach the mark on the end of the tubing.
A) Connect the “INPUT” water tubing from feed water adapter (Kl to “I
NPlJT” water port (H).
B) Connect the “Fl LTERED” w<1ter tubing from RO faucet (L) to “FILTERED”
water port (II).
C) Connect the •wASTE”water tubing from drain saddle (M) to”WASTE”water
port (J).
Step 6:
Connect Power Cord
- Insert faucet power cord into “faucet” connector (O-G).
- Connect Power Adapter to power port (F).
NOTE Please do not connect power socket (N) now.
Step 7:
Instilll the Filters
a: Insert the filter into its corresponding hole.
b: Rotate the filter clockwise l /4turn. You may hear a dicking sound
when the filter Is fitted into the place properly.
Step 8:
Start Up the System
- Turn on cold water supply valve and feed water adapter, connect power adapter.
- Wait for 5 minutes, allowing the system to flush automatically.
- Tum on RO faucet, allow it to run 30 minutes until the display screen shows TDS reading.
Display Screen and Filter Life Reminder
The screen display and indicator lights will go off after 5 minutes when the system stops making water.
Display Screen
TDS Display
The built-in TDS sensor detects the water quality when the system begins to
work, the front panel screen and RO faucet screen show above.
Flushing Display
Every time the system flushes, the front panel screen and RO faucet screen
show above.
Malfunction Display
When the system is in fault, the front pannel screen and RO faucet screen show
E02, E03, and E04. Please see the Instruction Manual for detailed solutions.
Filter Life Reminder
Indicator on System Housing
(Good)
Replace Soon
Replace Now
Indicator on RO Faucet
There are filter life indicators on system housing and RO faucet that notify you to perform routine filter replacement by color change .
Faucet Screen
| Remaining Life (Day)| Remaining Capacity (G)| Status
---|---|---|---
White
| >15| >40|
Good
Yellow
| 515| 40|
Replace Soon
Red
| 50| 50|
Replace Now
White Flash
(on RO faucet)
|
/
|
/
|
Flushing
Red Error
(on RO faucet)|
/
|
/
|
Malfunction
NOTE The indicators notify in accordance with usage time or processing capacity of the filters, whichever comes first.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>