Waterdrop WD-G3-N2RO Reverse Osmosis Water Filtration System Instruction Manual

Waterdrop WD-G3-N2RO Reverse Osmosis Water Filtration System

Specifications

• Model: WD-G3P600-RO
• Replacement for: Waterdrop Reverse Osmosis Water Filtration System WD-G3P600
• Filter life: Up to 24 months (varies based on local water quality)
• Certification: IAPMO R&T against NSF/ANSI Standard 58 and NSF/ANSI 372

Product Usage Instructions

Getting Started

1. Before removing the filter, turn off the faucet and wait for 30
   seconds to release internal pressure.

2. Twist off the old filter in a counterclockwise direction.

3. Remove shrink wrap and protective cap from the new filter.

4. Insert the new filter into the housing, aligning the arrow with the empty circle.

5. Apply slight forward pressure, and rotate the filter clockwise 1/4 turn until the arrow aligns with the solid circle.

6. Hold the RO filter life indicator for 7 seconds until the blue light stays on.

7. Turn on the RO faucet and flush for 30 minutes to get the TDS reading.

Storage and Maintenance

• Replace the filter regularly based on the filter life indicator.
• Do not store the filter for an extended period; keep it in a dry, cool place when not in use.
• Ensure the water source meets municipal tap water requirements.
• Avoid direct sunlight exposure.

Frequently Asked Questions

Q: Why does filtered water taste weird?

• A: The filtered water might taste weird due to an expiring filter.
• Check the indicator reminder and replace it if necessary.

Warning

• To avoid property damage from water leakage, follow installation instructions carefully.
• Misuse may void the warranty and result in the manufacturer disclaiming liability for damages.

Replacement Filter Installation Instruction

Replacement for the following water filtration system:

• Waterdrop Reverse Osmosis Water Filtration System WD-G3P600
• Filter life: Up to 24 months (which may vary according to local water quality)
• NOTE: Do not use water that is microbiologically unsafe or of unknown water quality without adequate disinfection.
• Certified by IAPMO R&T against NSF/ANSI Standard 58 in Model WD-G3P600 for the contaminants listed in the performance data sheet, and to NSF/ANSI 372 (≤0.25% lead).

Performance Data Sheet

Substance

| NSF Specified Challenge Concentration| Max Permissible Product Water Concentration| NSF Reduction Requirements
---|---|---|---
TDS| 750 ±40mg/L| /| ≥75%

Getting Started

With the leak-free design, filters could be replaced directly without cutting power and water or using tools.

1. Before removing the filter, please turn off the faucet first and wait for 30 to fully release the internal pressure of the RO system, which makes the filter easier to remove and install.
2. Twist the old filter in counterclockwise direction.
3. Remove the shrink wrap and protective cap from the new filter.
4. Insert the new filter into the housing, and align the arrow with the empty circle on the housing.
5. Apply slight forward pressure and rotate the filter clockwise 1/4 turn, until the arrow is aligned with the solid circle on the housing. You may hear a clicking sound when the filter is fitted in place.
6. Hold the RO filter life indicator for 7 seconds until the system beeps and the blue light stays on.
7. Turn on the RO faucet to flush for 30 minutes until the front panel screen and faucet screen display the TDS reading.

Storage and maintenance

• Replace the filter regularly according to the light of the filter life indicator.
• Do not store the filter for a long time, and place it in a dry, cool place when not in use.
• The water source needs to meet the requirements of municipal tap water.
• Avoid placing it in direct sunlight.

Frequently asked questions

Q: Why does filtered water taste weird?

• A: The filter is about to expire. Check the indicator reminder to confirm and replace it;
• The system hasn’t been used for a long time. Turn on the RO faucet, and allow it to flush for a while before drinking.

Q: What will happen if I do not change my filter when the filter life indicator light turns red?

• A: Over-used filter will degrade the filtration performance, causing contaminants to leak back into the water and adversely affect your health. It’s recommended to replace the filter if the filter life indicator turns red.

Q: Why is the filter life indicator still red after changing filter?

• A: Forget or fail to reset the filter life indicator. Please reset it again. Hold the CB filter reset indicator for 5 seconds until the system beeps and the blue light stays on.

Warning:

• To reduce the risk of property damage due to water leakage, this filter MUST be installed under the manufacturer’s specifications and instructions.
• Failure to follow instructions and operating specifications will void your warranty.
• Further, the manufacturer assumes no responsibility or liability for damages arising out of misuse of the product.

Manufacturer Technical Support

• Tel: 1-888-352-3558 (U.S.)
• E-mail:service@waterdropfilter.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>