ISAKE XG01 Dog Training Collar User Manual

ISAKE XG01 Dog Training Collar

Product Information

Specifications:

• Product Name : Dog Training Collar
• Compliance : Part 15 of FCC Rules
• Functions: Shock, Vibration, Sound
• Usage : Training for dogs

Product Usage Instructions

Pair the Remote with Receiver
Note: Remember the channel you have chosen to pair. Using another channel without pairing may result in a loss of control over the Receiver.

Test the Training Collar Set (After paired successfully)

1. Test the Shock function: Take out the test bulb and place it on the Receiver’s contact point. Press the Shock button to ensure the level is above 01. The test bulb should light up.
2. Test the Vibration function: Press the Vibration button to ensure the level is above 01. The Receiver should vibrate.
3. Test the Sound function: Press the Sound button (no need to adjust the level). The Receiver should emit a sound “bi~bi~”.

Key Definition

1. Antenna: transmit the signal strongly
2. LED light: Press ( 10) to light it, and press (10 ) again to turn it off.
3. LCD screen : Show the modes, levels, and channels
4. Shock button : Shock button: the screen is on, press to choose Shock mode, press or button to adjust the levels from 0–99, and press the Shock button again toMake the Receiver shock
5. Vibration button the screen is on, press to choose Vibration mode, press+or-button to adjust the levels from 0–99, and press the Shock button again to make the Receiver vibrate.
6. Sound button : press to choose Sound mode, don’t need to adjust the levels,just press to make the receiver sound ~
7. button: press – to reduce the levels.
8. Button: press + to increase the levels.
9. Channel button : choose your training channel among Ch1/CH2 /Ch3 by press this button.
10. Light button : Pressing to light the LED of the Remote, press again 9000 the LED will be off; IYoupress this button for 2 seconds, the white LED on the Receiver will be on, pressing2 seconds again, the White LED will be off If you don’t press it again,the White LED will be off automatically after 10 seconds.
11. Charging: hole of the Remote.
12. Power button : press to turn on the Receiver, present s again to turn it off
13. Charging : hole of the Receiver.
14. Contact points : to install the rubber cap, rh to the pet’s skin. Conduct the safe statics.
15. Indicator light : the light will flash when we press the shock/vibration /sound button; when charging, it’s on.

Pair the Remote With the Receiver

1. Press the shock button or vibration button to turn on the Remote
2. Choose a channel CH1 CH2 or CH3 by pressing the CH button
3. Adjust the level by pressing the + or – button, make sure the level is above 01
4. Press the Power button ofthe Receiver for 3 seconds, and you will hear a sound like Bee~, and the indicator light will flash; Then quickly, Press the vibration button or Shock button within 10 seconds after the sound Bee~, and you can hear a sound Bee~aain, which means the pairing successfully.
5. If you have 2 or 3 Receivers just choose the different channers, and pair them as per the above steps.

Note:
please remember the channel you have chosen to pair, it you use another channel without pair, you can’t control the Receiver.

Test the training collar set (After paired successfully)

1. Test the Shock function
   Take out the test bulb and put it on the Receiver’s contact point Press the Shock button and make sure the level is above 01) The test bulb will be on

2. Test the Vibration function
   Press the Vibration button ( make sure the level is above 01)The Receiver will vibrate

3. Test the Sound function
   Press the Sound button don’t need to adjust the level )The Receiver will sound bi~bi~

FCC Statement

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The device has evaluated to meet general RF exposure requirement. The device can be used be in portable exposure without restriction.

FAQ

Q: What should I do if the Receiver does not respond after pairing?
A: If the Receiver does not respond, try re-pairing the Remote and Receiver on the same channel. Ensure both devices are fully charged and within range.

Q: Can I use this collar for all dog sizes?
A: The collar is adjustable and suitable for most dog sizes. However, ensure it is not too tight or too loose on your dog’s neck for effective training.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>