Waterdrop LT600P-B Refrigerator Water Filter Instruction Manual

Waterdrop LT600P-B Refrigerator Water Filter

A replacement for the following water filters:

LG0 filters
LT600P0 LT600P-B, LT600PC, 5231 JA2006, 5231 JA2006A, 5231 JA2006A-S, 5231JA2006B, 5231JA2006B-S, 5231JA2006E, 5231JA2006F, 5231JA2006F-S, 5231JA2006H, 5231JA2005A, 5231JA2005A-S, 5231JJ2001C, CLS30320001

Sears• I Kenmore• filters
9990, 9990P, 469990, 46-9990, 04609990000

Installation instructions

Before installation:

• Shut off the cold-water supply to the refrigerator before installation. Turn on the refrigerator water dispenser to release water pressure, letting water drain from the pipe completely.
• It is normal for black carbon fines (particles) to appear on the outside of your filter. This happens when the filter is jarred in shipping. It is safe to simply wipe it off.
• The filter connectors are larger to prevent leaks. You might have to twist the filter hard to make sure the connection is secure.

1. Turn the knob counterclockwise by a quarter until it is completely vertical, then remove it. The filter will eject slightly with a clicking sound.
   Note: A filter that is not completely vertical cannot be removed, and forcing it out will prevent the installation of a new filter

2. Holding the new filter in your hands, carefully remove the packaging and sanitary end-cap from the new filter.

3. Insert the new filter into the refrigerator filter receptacle. With the handle in the vertical position, push the new filter into the housing until it stops. When inserting the new filter, twist the handle slightly left to right, while pushing inward. Rotate the filter clockwise a full 1/4 turn until you feel it stop. Ensure filter is fully installed in refrigerator head a full 1/4 turn. This is required to activate the internal valve inside the refrigerator. If the filter is not turned a full 1/4 turn the valve will not fully open and may cause the water flow to be slow, or even cause the valve to make a chattering noise during use.
4. Check filter one more time for any leaks.
5. Run water from the dispenser for 5 minutes at 0.5 gpm (about 2.5 gallons) to clear the system and prevent sputtering.

Resetting your filter indicator

Note: These are the most common filter reset instructions. If the instructions don’t work for your refrigerator brand, see the documentation that came with your refrigerator.

Storage and maintenance

• Replace your filter every 6 months or 300 gallons to prevent bacteria and fungus growth in your filter, supply lines, and storage tank.
• Keep your unused filters in a cool, dark, and dry place until you need them.
• If you do not use your water dispenser for more than four days, run two gallons of water before using it to prevent bad tasting water.

Frequently asked questions

• Why is it difficult to twist the new filter into the filter housing?
  The connector may expand because of water pressure. Therefore, it is recommended you push the new filter in with a little bit of force, but not too hard. Then turn it clockwise.

• Do I need to flush the filter after installation?
  After installation, it is highly recommended you run water for a few minutes before using. Water filters are made from advanced coconut carbon block, so there are some carbon fines in the filter. Flushing removes the carbon fines to produce clean water.

• Must the filter be changed every 6 months?
  Yes, you must replace the filter every six months or sooner if water flow is reduced or if there is heavy sediment / rust present. Over-used filters will degrade the filtration performance.

Warning:

• To reduce the risk of property damage due to water leakage, this filter MUST be installed in accordance with the manufacturer’s specifications and instructions. This filter unit must be replaced every 300 gallons or 6 months.
• Failure to follow instructions and operating specifications will void your warranty. Further, manufacturer assumes no responsibility or liability for damages arising out of misuse of the product. LG” is a registered trademark of LG CORP.
• LG is used for reference purposes only.
• Kenmore is a registered trademark of KCD IP, LLC.
• Kenmore is used for reference purposes only.
• The service life mentioned above is subject to chlorine reduction.
• Actual result varies according to the local water quality.

Operating specifications

• Operating Temperature: 33°F – 100°F/0.6°C- 38°C
• Working Pressure: 20 psi -100 psi/140 kPa – 689 kPa
• Rated Capacity: 300 gallons/I, 137 litres
• Flow Rate: 0.5 gpm/1.9 lpm

Substance reduction

The system has been tested and certified by the NSF International according to NSF/ANSI Standard 42 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for the water leaving the system, as specified by NSF/ ANSI Standard 42. While testing was performed under standard laboratory conditions, actual performance may vary.

  Substance|   Inf.Average| NSF Specified

Challenge Concentration

| Ave.%

Reduction(%)

| Average Product Water Concentration| Max Permissible Product Water Concentration| NSF Reduction Requirements| NSFTest

Report

---|---|---|---|---|---|---|---
Chlorine Taste and Odor| 2.1 mg/L| 2.0mg/L±10%| 97.0%| 0.063mg/L| N/A| SO%| J00295S02

Do not use with water that is microbiologically unsafe or of unknown water quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used with disinfected water that may contain filterable cysts.

Manufacturer Technical Support

• Tel: 1-888-352-3558 (U.S.)
• E-mail: service@water-filter.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>