maxpower MPD1240-XB Professional Speaker User Manual
- June 15, 2024
- maxpower
Table of Contents
max power MPD1240-XB Professional Speaker
PLEASE READ THIS USER MANUAL CAREFULLY BEFORE THE SYSTEM CONNECT.
IMPORTANT SAFETY MEASURES
Before using this machine, please read all the safety and operating instructions, meanwhile, please observe all the indications about safe operating. These safety and operating instructions should be kept in condition of consultation.
- Protection of electric power supply line: Be aware that the electric power supply line is not tramped, or pressed by heavy objects.
- Pay special attention to the plug of the power supply line and outlet on the machine. DO NOT lengthen the electric shock, DO NOT pull or drag the power supply line.
- Ventilation: This set must be put in a ventilated place. DO NOT put the disk on it or cloth to cover it. The distance away from the wall should not be less than 10 centimetres.
- DO NOT put this set on the bed sofa, carpet or other objects with similar surfaces in case of good ventilation.
- Casing Dismantling: DO NOT dismantle the casing. If one touches the inner components, he will probably get a serious electric shock
- Unusual smell: When you discover an unusual smell and smoke, cut power supplies immediately and pull out the plug from the outlet on the wall. Contact the sales shop or nearest repair centre.
- Attention: This set applies to AC 110V / 50Hz~60Hz power supply. Use a standard power supply. Please be sure for the correct power supply before using it.
PRODUCT FEATURES
- Wireless
- Plays songs stored in an external audio device.
- Guitar input Microphone inputs
- Wireless microphone included
- With remote control
- Built-in rechargeable battery Super dynamic sound speaker
- X-Bass is powerful
REMOTE CONTROL
CONNECTING
- This set applies to AC 110V, 50/60Hz
- AC power: the battery can be charged when connected to AC power.
- The red light on the battery is charging, it will change to green once the battery is fully charged.
- The internal battery will be charged even if the device is switched off when plugged into AC power
- The speaker battery can be charged using a 12V external car battery as well(connect cable not included) by “DC 12V input”. Please make sure “+” and “-” are in the right connection.
- Adjust function keys to your personal audio preference.
BATTERY & CHARGING
- The units take approximately 8 hours to fully charge. It will automatically begin charging once the power cord is connected.
- If the battery power is low may cause sound distortion or stop playing, please charge the battery on time.
- To maximize the battery’s lifespan, please charge the battery immediately. When the unit is not used for prolonged periods, the battery will gradually lose its power.
- It is recommended to fully charge the battery at least every 30 days.
- To save battery, please power it off once stop using it.
HOW TO CONNECT TO BT
When you turn on the speaker, the display will read OPEN which means your
speaker is ready to connect. Go to your smart device and search for your BT
device. You will see the device name MPD1240-XB and please select that. Please
select
MPD1240-XB and you will be connected.
For the TWS CONNECTION -HOW TO PAIR TWO SPEAKERS
First, bring two speakers next to each other, and turn on both speakers. Both
the speaker’s display should read open. For the first speaker/primary speaker,
please press and hold the TWS button for 3 seconds. The primary speaker will
sound an alarm and the display will show “BTST” and the second speaker
automatically connects to the primary speaker. The display of the secondary
speaker will say BT. Now you may connect to BT from your smart device and
listen to
music from both your speakers.
PANEL FUNCTION INSTRUCTION
- MIC. VOL MICROPHONE VOLUME ADJUST
- MODE — MODE SELECT REPEAT KEY
- REC: RECORDING; INSERT CARD PRESS THIS
- BUTTON FOR RECORDING, PRESS AGAIN TO STOP AND
- PLAY RECORDING SOUND DC 12V INPUT AUDIO INPUT
- PRI MICROPHONE PRIORITY ON/OFF SWITCH
- IN GUITAR INPUT JACK MIC.IN MICROPHONE INPUT JACK
- EQUALIZER POWER ON/OFF SWITCH, RESET
- DISPLAY SCREEN CARD INPUT
- MIC.BASS VOLUME KNOB: INCREASE/DECREASE MICROPHONE BASSMIC.MID VOLUME KNOB: INCREASE/DECREASE MICROPHONE TREBLE MIC.
- TREBLE VOLUME KNOB: INCREASE/DECREASE MICROPHONE TR EBLE SCAN/TWS: PLAY/PAUSE/TWS/FM STATION AUTOMATIC SEARCH
- PREV: PREVIOUS SONG
- NEXT: NEXT SONG VOLUME MASTER VOLUME ADJUST
- ECHO KNOB BT DISCONNECT
- X-BASS: INCREASE/DECREASE X-BASS
- LED MODE ADJUSTMENT VOLUME
FCC STATEMENT
This equipment has been tested and found to comply with the limits of a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.