IBEX 10008014 Central Stand For Kawasaki Instruction Manual

IBEX 10008014 Central Stand For Kawasaki

Product Information

Specifications

• RAL : 9005
• Color:  jet black)

General Notes
Observe any country-specific regulations by the legislature or homologation regulations.
Preparation
Before starting the assembly, ensure you have read and understood the assembly instructions provided. Also, refer to the relevant notes in the vehicle manual.

Assembling
Follow these steps to assemble the product:

1. According to the vehicle manufacturer’s specifications, reassemble or replace all demounted parts and connections with the parts and connections supplied by our company.
2. If not stated otherwise, secure all threads with a medium-strong liquid screw protection.
3. If not stated otherwise by the vehicle manufacturer or our company, tighten all bolts and nuts according to A4/ISO standards.
4. After assembly, ensure that all previously demounted parts and connections have been properly remounted.

Function Check
After assembly, perform a comprehensive functional check before starting your journey:

• Ensure absolute freedom of movement and proper function of all vehicle parts.
• Check that cables, trains, and hoses are not scrubbing or clamped.

After driving 100 km, check the proper tightness of all parts and connections that were demounted during assembly.

Legend
Contact Information

• Email: [email protected]
• Tel.: 0351/27278100
• Fax: 0351/27278101

Errors and Changes
Errors and changes are expected. The product is subject to technical and design changes.

FAQ

1. Q: Can I use this product without reducing the cornering and ground clearance?
   A: No, using this product may reduce the cornering and ground clearance of your vehicle.

2. Q: Is it recommended to have the installation and servicing done by a specialist workshop?
   A: Yes, for your own safety, we recommend having installation and/or servicing carried out by a specialist workshop. We assume no liability for damage caused by improper installation and/or maintenance work.

3. Q: What should I do if I encounter any damage during the assembly or maintenance of the product?
   A: Please ensure that you have a good technical understanding and carefully follow all the notes provided in the assembly instructions. Failure to observe these instructions can cause damage to the vehicle or pose a danger to the driver.

Mounting Instruction

• Rev:
  • ./.
• Date of issue:
  • 03.11.2020

Centerstand kit

ATTENTION

• Cornering and ground clearance can be reduced by using this product!
• For your own safety we recommend having installation and/ or servicing carried out by a specialist workshop. We assumes no liability for damage caused by improper installation and/ or maintenance work.
• No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer´s specifications

Thank you for choosing this quality product from IBEX!

• The assembly and/or maintenance of this product requires a good technical understanding. For your own safety, we recommend that the assembly and/or maintenance is carried out by a specialist workshop. Our company assumes no liability for any damage caused by improper assembly or maintenance. Be sure to keep in mind all the notes provided in the assembly instructions. Please also note all the instructions relevant to the assembly in the vehicle manual. Nonobservance can cause damage to the vehicle or danger to the driver! Please keep the assembly instructions as a reference.

• General Notes:
  Observe any country-specific regulations by the legislature or homologation regulations.

• Preparation:
  Read the assembly instructions carefully and make sure all parts of the list are available. Make sure that your vehicle stands safely and can´t fall over. Turn off the engine and pull the ignition key. If necessary, allow the engine/exhaust to cool down. When working on the electrics disconnect the vehicle battery. Be sure to use only suitable tools. If necessary get help with the assembly work by a second person.

• Assembling:
  According to vehicle manufacturers specification all demounted parts and connections must be reassembled or replaced by the parts and connections supplied by our company. If not stated different secure all threads with a medium-strong liquid screw protection. If not stated different by the vehicle manufacturer or our company, all bolts and nuts must be tightened according to A4/ISO. After assembly, make sure that all previously demounted parts and connections have been properly remounted.

• Function Check:
  After assembly, pay attention to the absolute freedom of movement and proper function of all vehicle parts. Cables, trains and hoses must not scrub or be clamped. Do a comprehensive functional check before the start of your journey. After 100 km please check the proper tightness of all parts and connections demounted during assembly

• (packed by)

  • (packaging date)

• Email: [email protected]

• Tel.: 0351/ 27278100

• Fax: 0351/ 27278101

OVERVEIW

• Copyright by:
  • IBEX GmbH Sosaer Straße 35 01257 Dresden
• Errors and changes expected. Subject to technical and design changes.

References

• Forside - POS.no

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>