SOLIGHT 1L71 Wireless Doorbell with Electrical Socket Instruction Manual

SOLIGHT 1L71 Wireless Doorbell with Electrical Socket

Specifications

• Product Name: EN 1L71 Wireless Doorbell with Electrical Socket
• Power Supply: Max. AC 250V, 50Hz
• Electric Outlet: Max. AC 250V/16A, 3680W/230V~
• Volume Settings: 4 modes, 20-80 dB
• Working Frequency: 433.92 MHz
• Receiver Standby Power: N/A (Dependent on electric socket power)
• Transmitter Operating Power: Dependent on battery power
• Melody: Various options available
• Reach: Varies depending on the environment
• Transmitter Coverage: Varies depending on the environment
• Power Button: Included on the transmitter and receiver

Product Usage Instructions

Setting Up the Doorbell

1. Plug the wireless doorbell receiver into an electrical socket.
2. Ensure the receiver is receiving power by pressing the power button on the receiver. A light signal should indicate that it’s powered on.
3. Install the batteries into the transmitter, ensuring they are properly inserted.
4. Mount the transmitter outside your door using screws or adhesive tape. Make sure it is securely attached and protected from rain or direct sunlight.

Volume Settings
The wireless doorbell offers four volume settings to suit your preferences. Follow these steps to adjust the volume:

1. Press the power button on the receiver to activate it.
2. Press the volume button on the receiver repeatedly to cycle through the available volume levels. The doorbell will play a sample melody at each level, indicating the current volume setting.
3. Release the volume button when you reach your desired volume level.

Melody Settings
The doorbell provides multiple melody options for customization.
To change the melody:

1. Press and hold the melody button on the receiver for a few seconds until you hear a beep or see a light signal, indicating that the melody selection mode is activated.
2. Press the melody button repeatedly to cycle through the available melodies.
3. Release the melody button when you find your desired melody.

Light Signalization Settings
The wireless doorbell offers different light signalization modes. To change the light signalization setting:

1. Press and hold the power button on the receiver for a few seconds until you hear a beep or see a light signal, indicating that the light signalization mode is activated.
2. Press the power button repeatedly to cycle through the available light signalization modes. Each mode has a specific combination of ringing and light signals.
3. Release the power button when you reach your desired light signalization mode.

Frequently Asked Questions (FAQ)

• How far is the reach of the wireless doorbell?
  The reach of the wireless doorbell may vary depending on environmental factors such as walls and interference. Generally, it can cover a range of up to 100 meters in an open area.

• Can I use the wireless doorbell with multiple transmitters?
  Yes, you can pair multiple transmitters with a single receiver. Follow the pairing instructions in the user manual to add additional transmitters.

• Can I change the batteries in the transmitter?
  Yes, the transmitter uses replaceable batteries. Refer to the user manual for instructions on how to replace the batteries.

INTRODUCTION

Thank you for purchasing our wireless doorbell with power outlet. The set consists of a bell button (transmitter) and a bell (receiver). The doorbell is designed for permanent connection to a 230 V AC/50 Hz power supply. The transmission between the button and the doorbell is via radio waves with a frequency of 433.92 MHz. The range depends on local conditions and can reach up to 250 m in open spaces without interference. The set has a so-called pairing function (Learning code) – the button is able to generate its own pairing code, which is received by the doorbell and stored in its memory. The set can thus be expanded with additional transmitters or receivers. The pairing function also prevents the set from affecting neighbouring bells. For proper use, read the instruction manual.

PRODUCT OVERVIEW

Setting the light/sound signalization

1. Ringing + light signalization
2. Ringing only
3. Only light signalization
4. Continuous light signalization + ringing

Technical parameters

• Doorbell power supply max. AC 250V, 50Hz
• Continuous electric socket max. AC 250V/16A, 3680W/230V~
• Volume 4 modes , 20-80 dB
• Working frequency 433.92 MHz
• Receiver standby power <0.5W
• Transmitter operating power <10mW
• Melody 58 melodies
• Reach Up to 250m in open space
• Transmitter Coverage IP55
• Power button CR2032 battery (included)

Installation

1. Tear off one side of the double-sided adhesive tape and stick it to the underside of the button (transmitter).
2. Tear off the other side of the double-sided adhesive tape.
3. Select a suitable place and stick the button. If a stronger fixing is needed, use dowels and screws – open the button (see battery replacement), drill holes in the marked circular slots on the inside of the button cover and screw it to the base. Then cover the other part of the button and press the two parts together.
4. Connect the doorbell (receiver) to an electrical socket
5. Select the melody, volume or type of signaling

Replacing the battery

Using a flathead screwdriver push into the groove of the joint on the short side of the button and open the cover . Insert the CR2032 battery, observing the marked polarity. Then close the cover.

“Code Learning” function

The device has already been paired in production. If you need to change the transmitter, increase or decrease the number of bells or buttons in a group, follow the steps below:

1. Pairing
   Press and hold the button for “Setting the light/sound signalization” until the device emits a bird whistle sound. Then, within 30 seconds, press the button on the transmitter. If the bell rings, the pairing is successful. If the bell does not ring, press the transmitter again until pairing is successful. To pair multiple transmitters, repeat the above operation. A maximum of 8 buttons can be paired to one doorbell. One button can be paired with a maximum of 20 bells, and a different melody can be set on each bell.

2. Cancel pairing
   Press and hold the “Setting the light/sound signalization” button for about 10 seconds until the chime (ding dong) sounds twice. This cancels the pairing. Before the sound of the bell (ding dong) there is usually a bird whistle – do not release the button at this time and wait for the ding dong melody.

Notice

1. Do not disassemble or repair the equipment.
2. Operating range may be affected by environmental factors and nearby interference sources.
3. Proper use will effectively extend the life of the equipment.
4. Disconnect the receiver from the mains before cleaning. Use only a dry soft cloth for cleaning. If you use wet cleaning, use only cleaning agents free of aggressive compounds and reagents and allow to dry thoroughly. Do not immerse the product in water! Protect the product from contact with fluxes and places of high temperature.

Troubleshooting

If the receiver does not ring repeatedly after pressing the button on the transmitter, check:

• whether the distance between the transmitter and the receiver is too large
• that there are no strong sources of signal interference between the transmitter and receiver (radio and wireless networks, large metal objects, reinforced concrete walls, etc.)

DISPOSAL

Solight Holding s.r.o., declares that the product complies with the requirements and provisions of Directive 2014/53/EU. The equipment can be freely operated in the EU. The Declaration of Conformity can be found at www.solight.cz. The product can be operated under general authorisation No.VO-R/10/05.2014-3

ABOUT COMPANY

Producer:
Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, www.solight.cz

References

• SOLIGHT.cz | Váš B2B partner a velkoobchod pro Osvětlení, Elektro, Smart Home, Měřící techniku a dalších 1500+ produktů

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>