MOUNTUP MU6002-A Dual Monitor Desk Mount Instruction Manual

June 15, 2024
MOUNTUP

MOUNTUP Logo Dual Monitor Desk Mount
Instruction ManualMOUNTUP MU6002 A Dual Monitor Desk Mount

80002-MA11-24-US4.0
If you have any questions, please feel free to contact Customer Service via Amazon before returning.

WARNING!

If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specited, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

MOUNTUP MU6002 A Dual Monitor Desk Mount  - PACKAGE
CONTENTS DO NOT EXCEED WEIGHT CAPACITY.

ASSEMBLY STEPS

Warm Tips You could also refer to the Video Guide about installation on our product page.
STEP 1: Apply Pads to the Base Bottom
Apply pads (E1&E2) to the base bottom to avoid desk scratches.

MOUNTUP MU6002 A Dual Monitor Desk Mount  - STEPS

STEP 2: Clamp Installation or Grommet Base Installation
OPTION A: Clamp Installation
Remove the plastic cover from Base (C).
Mount Clamp (D) to the bottom of Base (C) by tightening bolts (K) with 5mm Allen Key (I).

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Grommet

Adjust the Clamp width to fit your desk.
Secure stand to the desktop by tightening clamp (D). Fix the plastic cover to Base (C).

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Grommet 1

STEP 2: (Continued)
OPTION B: Grommet Base Installation
If existing grommet hole comes with a plastic protector, remove it to ensure a fat surface before installing the desk mount.
Firstly detach Bracket (D1) from Clamp (D).

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Grommet 2

By tightening Wingnut (F) after making Bracket (D1) through Carriage Bolt (G) and stacked above Wingnut (F), Base (C) would be fixed to your desk securely. Install the plastic cover to Base (C) finally.

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Grommet 3

STEP 3: Arm Installation
Install the lower arm (B) to the base (C). Secure the arm by tightening the inside screw using 3mm Allen key (H).
Note: If VESA plate is crooked, please hold it with both hands and rotate vigorously to make up arrows pointing up.

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Arm

STEP 4: Attach Monitor

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Arm

STEP 5: Tilt Adjustment
Problem:
Monitor tilts down.

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Monitor
tilts

Solution:

  1. Loosen the tilting bolt.
  2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Solution

STEP 6: Adjust Tension
The gas spring is pre-set to minimum tension. For intended functioning of the mount, you will need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J).

MOUNTUP MU6002 A Dual Monitor Desk Mount  - Adjust
Tension

NOTE:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be dificult to adjust the mount or damage the mount.
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
S olution:
Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up or can’t press down
Upper Arm with monitor rises up and fails to stay where intended.
Solution:
Turn the inside screw clockwise(“-”direction) to decrease gas spring tension until the arm can stay as intended.

MOUNTUP MU6002 A Dual Monitor Desk Mount  -Upper Arm 1

STEP 7: Cable Management
7-1 Remove Cable Cover

  • For lower arm: Remove the bottom plastic cover from lower arm as shown in the diagram below.

MOUNTUP MU6002 A Dual Monitor Desk Mount  -Management

7-2 Attach Cable Cover

  • For lower arm: Run cables through the cable cover, then insert and slide the cover down for reattachment;
  • For upper arm: Run cables through the cable cover, then with both hands slightly press inwards the tabs inside the cover and insert it to upper arm.

MOUNTUP MU6002 A Dual Monitor Desk Mount  -Cable Cover

Adjust as Desired

Adjust monitor position and rotation.

MOUNTUP MU6002 A Dual Monitor Desk Mount  -Adjust as
Desired

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of dificult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Product Dimensions

MOUNTUP MU6002 A Dual Monitor Desk Mount  -Adjust as Desired
2

CAUTION AND MAINTENANCE:

  • Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.
  • Check if that the bracket is secure and safe to use at regular intervals (at least every three months).

MOUNTUP Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals