typecase 201T-12.9 Touch iPad Pro 12.9 2021 Case with Keyboard User Manual
- June 15, 2024
- typecase
Table of Contents
201T-12.9 Touch iPad Pro 12.9 2021 Case with Keyboard
User Manual
For warranty registration and product support:
typecase.co/resources
+1(832) 303-5080
[email protected]
TECHNICAL SUPPORT
lf you encounter any difficulties or have inquiries, please do not hesitate to
reach out to us at your earliest convenience.
For the quickest and most efficient support experience, please contact us
directly through one of the following channels, rather than through Amazon.
- Email: [email protected]
- Phone: 832 – 303 – 5080
- Chat: https://typecase.co/support
COMPATIBILITY
Compatible with iPadOS 13 (and newer). We recommend updating your iPadOS to 16
for best perormance.
To check your iPad system version:
- Go to Settings > General > About > Software Version.
- Upgrade your version to iPadOS 16 or above to use the touchpad function correctly.
To upgrade your iPadOS to the lastest version:
- Open your device’s Settings > General > Software Update.
- Tap Download and Install.
- If you see Resume Download, tap that instead.
SETUP
To pair with your iPad:
- Long Press for 2 seconds, the Power indicator will be on for 3 seconds
- The Bluetooth indicator light will start to blink. If it doesn’t, hold down the button for 2 seconds.
- Go to the Settings app and turn on Bluetooth. (The device is connected when the Bluetooth indicator stops flashing.)
- In the Bluetooth section of the Settings app, select ‘Typecase EDGE’ under ‘MY DEVICES’.
- Tap ‘Pair’ in the pop-up window as shown.
*Note: To pair with new devices, repeat moc el Pair steps 1-3.
The pairing process is complete when you see the ‘Connected!’ indicator.
If your system is 13.3.1, please follow the steps to enable touchpad function:
- Go to Settings >- Accessibility > Touch.
- Make sure Assistive Touch option is turned On.
SHORTCUT MAP
Notice: Long press in any app to view available shortcuts.
Keyboard
System
Multitasking
Spilt View
Slide Over
Edit
Formate
Symbol
TOUCHPAD FUNCTION
Notice: Make sure bluetooth connected and touchpad function turned on!
| Tap
Tap with a single finger until it feels a little touch feeling.| | Tap and
Hold
Tap and hold with a single finger.
---|---|---|---
| Drag
Tap and hold an item, then swipe your finger across the trackpad to move it.|
| Awake
Click the touchpad or press any key on the keyboard.
| Open Program Expansion Dock
Swipe the pointer across the bottom of the screen with one finger.| | Go To
Home Screen
Swipe the pointer across the bottom of the screen with one finger, and when
the Dock appears, swipe the pointer across the bottom of the screen again.
| View Slide Over
Use one finger to swipe the pointer past the right edge of the screen. To hide
Slide Over, swipe right again.| | Open Notification Center
Use one finger to move the pointer to select the status icons at the top left,
then click.
Or, use one finger to move the pointer past the top of the screen near the
middle.
| Open Control Center
Use one finger to move the pointer to select the status icons at the top
right, then click.
Or, select the status icons at the top right, then swipe up with one finger.|
| Move Left Or Right
Swipe left or right with two fingers.
| Move Up Or Down
Swipe up or down with two fingers.| | Open Searching From Home Screen
Swipe down with two fingers.
| Zoom
Place two fingers close together, open to enlarge, or pinch to zoom out.| |
Secondary click
Click with two fingers to show the quick actions menu for items like icons on
the Home Screen, messages in a mailbox, and the Camera button in Control
Center.
Or, you can press the Control key while you click the trackpad.
| Open”Today” View
When the Home or Lock screen is visible, swipe right with two fingers.| |
Go To Home Screen
Swipe up with three fingers.
| Open APP Switcher
Swipe up with three fingers, pause and lift your finger.| | Shift Between
The Open APP
Swipe left or right with three fingers.
INSTALLATION AND REMOVAL
| Installation | Removal |
|---|
| 
CHARGING
- Switch on the keyboard (if battery light is flashing, please charge the keyboard).
- Plug the charging cable (included) into the keyboard and power adapter (not included, iPad or iPhone power adapter recommended);
a) Battery indicator turns red when keyboard is charging;
b) Battery indicator turns blue when charging is complete.
TROUBLESHOOTING
If the keyboard is not working correctly, please check the following:
- The Bluetooth function on the iPad (or other Bluetooth devices) is enabled;
- The Bluetooth keyboard is within 33 feet;
- The Bluetooth keyboard is charged;
- Make sure the keyboard is turned on (the battery indicator is illuminated);
- Press the key and check the Bluetooth status;
- Make sure a keyboard has already paired via Bluetooth.
If you don’t need auto-correction or punctuation, please follow these steps:
- Open Settings app > General > Keyboard > Hardware Keyboard;
- Toggle OFF Auto-Capitalization, Auto-Correction, and “.” shortcut (please refer to the picture below).
If Bluetooth pairing fails, please try the following steps:
- Remove all Bluetooth devices on your iPad;
- Switch off the Bluetooth function on your iPad;
- Reboot the iPad;
- Turnon the Bluetooth on your iPad;
- Switch the keyboard off and on;
- Repeat the steps described on page 2 and 3 to pair the keyboard.
PRODUCT SPECS
Operating distance: 10 meters (33 feet)
Modulation System: GFSK
Working voltage: 3.0-4.2V
Working current: 0.88-200mA
Sleeping current: < 125A
Charging current: <800mA
Continuous working time without backlight: 60 hours
Charging time: <2.5hours
Charging voltage: 5V
Key’s life span: > 5 million strokes
Operating temperature: -10 ±55°C
Maintenance: Please preserve the keyboard under normal temperature and
recharge under normal voltage.
IC CAUTION
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference,and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
FCC CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.