MOUNTUP MU2009 Single Monitor Wall Mount User Manual

June 15, 2024
MOUNTUP

INSTALLATION INSTRUCTION
YZ2315_US2.0

MOUNTUP MU2009 Single Monitor Wall Mount - overview 1

If you have any questions, please feel free to contact Customer Service via Amazon before returning.

Supplied Parts and Hardware

MOUNTUP MU2009 Single Monitor Wall Mount - Supplied Parts and Hardware
1

MOUNTUP MU2009 Single Monitor Wall Mount - Supplied Parts and Hardware
2

Extra Tools You Need (Not Supplied)

MOUNTUP MU2009 Single Monitor Wall Mount - Extra Tools You Need
1

Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product,
please contact us.

  • This product is designed for use in wood stud or solid concrete wall.
    – DO NOT install into drywall alone.

  • The wall must be capable of supporting five times the weight of the monitor and mount combined.

  • Incorrect installation may result in product damage/property damage or body injury.
    We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!

Must Check Before Getting Started

MOUNTUP MU2009 Single Monitor Wall Mount - Must Check Before Getting Started
1

Attention
Tension adjustment should be done only after monitor installation

WARNING:
Gas Spring Arm is under pressure and should be handled with care. Failure to follow the instructions may result in damage to the mount and/or personal injury.

Attach VESA Plate to Monitor

1-1 Select VESA Plate Configuration
Measure the width and the height of the square or rectangle formed from the VESA holes pattern. Select the configuration to use based on the measurement from monitor.

VESA Pattern (WxH)| Configuration| VESA Pattern (WxH)| Configuration
---|---|---|---
75mm x 75mm| A| 200mm x 100mm| B
100mm x 100mm| A| 200mm x 200mm| B
150mm x 150mm| B| 100mm x 200mm| C

MOUNTUP MU2009 Single Monitor Wall Mount - Attach VESA Plate to Monitor
2

Assemble Extenders (When VESA > 100mm)
If your monitor hole pattern is greater than 100×100mm, attach extenders (L) to VESA plate (E) using nuts (J) and bolts (K).

MOUNTUP MU2009 Single Monitor Wall Mount - Attach VESA Plate to Monitor
3

1-2 Select Correct Monitor Screw Length

MOUNTUP MU2009 Single Monitor Wall Mount - Attach VESA Plate to Monitor
4

Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the appropriate screws and spacers for your monitor.

MOUNTUP MU2009 Single Monitor Wall Mount - Attach VESA Plate to Monitor
5

1-3

MOUNTUP MU2009 Single Monitor Wall Mount - Attach VESA Plate to Monitor
6

| Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged.
---|---

A Attach Arm to Wall

OPTION A: Wood Stud Installation

MOUNTUP MU2009 Single Monitor Wall Mount - Attach Arm to Wall
1

Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.
Position the wall plate at your desired height and line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations.

A-2

MOUNTUP MU2009 Single Monitor Wall Mount - Attach Arm to Wall
2

Drill pilot holes using a
Ф3/16 in (Ф4.5mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be sure to drill into the center of the stud.

A-3

MOUNTUP MU2009 Single Monitor Wall Mount - Attach Arm to Wall
3

Install wall plate using lag bolts W-A with Socket Wrench, NO Electrodrill.
No anchors when installed onto the wood studs.

CAUTION:
To avoid potential personal injury or property damage:
All 3 lag bolts W-A MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.

B Attach Arm to Wall
OPTION B: Solid Concrete Wall Installation

B-1

Level the wall plate and mark the pilot hole locations.

B-2

MOUNTUP MU2009 Single Monitor Wall Mount - Attach Arm to Wall
5

Drill pilot holes using a Ф3/8 in (Ф10mm) diameter drill bit.

IMPORTANT: Do not drill holes into where water pipes or electrical wires are located, or mortar between blocks.

B-3

MOUNTUP MU2009 Single Monitor Wall Mount - Attach Arm to Wall
6

Use the hammer to knock anchors into the concrete wall. Be sure the anchors are seated flush with the concrete surface. Install wall plate using lag bolts W-A and anchors W-B with Socket Wrench, NO Electrodrill.

CAUTION:
To avoid potential personal injury or property damage:
All 3 lag bolts W-A MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.

Hang Monitor

Install the Upper Arm (B) to the Lower Arm (A). Secure the arm by tightening the inside screw using 3mm Allen key (G). Attach Decorative Covers (C) to wall plate.

MOUNTUP MU2009 Single Monitor Wall Mount - Hang Monitor
1

MOUNTUP MU2009 Single Monitor Wall Mount - Hang Monitor
2

Slide the monitor onto the head of swivel arm, install the security bolt (F).
Make sure the security bolt is installed before you rotate the monitor.

MOUNTUP MU2009 Single Monitor Wall Mount - Hang Monitor
3

Adjustments (If necessary)

4-1 Tilt Adjustment

  1. Loosen the tilting bolt.
  2. Adjust monitor to your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.

MOUNTUP MU2009 Single Monitor Wall Mount - Adjustments
1

4-2 Tension Adjustment
The gas spring is pre-set for a load-bearing range of 8.8 lbs -13.2 lbs. For intended functioning of the mount, you will need to adjust the tension of Arm in accordance with your monitor weight by 6mm Allen Key (H).

MOUNTUP MU2009 Single Monitor Wall Mount - Adjustments
2

Note:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.

Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.

Solution:
Turn the inside screw counterclockwise (“+”direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up or can’t press down
Upper Arm with monitor rises up and fails to stay where intended.

Solution:
Turn the inside screw clockwise (“-”direction) to decrease gas spring tension until the arm can stay as intended.

Cable Management

MOUNTUP MU2009 Single Monitor Wall Mount - Cable Management
1

Adjust monitor position and rotation.

MOUNTUP MU2009 Single Monitor Wall Mount - Cable Management
2

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals