EDIFIER GM3 Plus True Wireless Gaming Earbuds User Manual
- June 4, 2024
- Edifier
Table of Contents
EDIFIER GM3 Plus True Wireless Gaming Earbuds
Product Description and Accessories
- Earbuds
- Charging case
- Charging cable
- Brand card
- Brand sticker
- User manual
Note:
- Please do not charge the product when there is sweat or other liquids inside the charging port, which may damage the product.
- Images are for illustrative purposes only and may differ from the actual product.
Power ON/OFF
- Power ON: Take earbuds out of the charging case, or press and hold the touch panel for 3s.
- Power OFF: Put the earbuds in the charging case. The earbuds will power off automatically if there is no connection after 3 minutes.
Charge
Earbuds
Place the earbuds in the charging case for charging.
After the indicator on the charging case turn on to indicate battery level:
LED on the left lit in a breathing pattern = left earbud is charged
LED on the right lit in a breathing pattern = right earbud is charged LED off =
fully charged
Charging case
Red LED lit in a breathing pattern = charging LED off = fully charged Charging
time: around 1.5 hours
Input: 5V 200mA(Earbuds) 5V 1A(Charging case)
Battery level
Pairing
- For initial use, the earbuds will auto-on and enter Bluetooth pairing state when taken out of the case (prompt tone: Pairing).
- Select “HECATE GM3 Plus” in your device setting to connect, wait until you hear the prompt tone of “Connected”, then the pairing is successful.
Note:
- For devices paired successfully before, the earbuds will auto-connect to device used last time.
- If cannot connect to device used last time in 3 minutes, the earbuds will turn off automatically.
Reset
In OFF state, press and hold either earbud for 8s to reset. The reset is successful when hearing the prompt tone of “Power on”, “Pairing” and “Power off” one after another.
Controls
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment could be installed and operated with minimum distance 0 cm between the radiator and your body. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.IC statement:CAN ICES-003(B)/NMB-003(B).
Declaration for EU
- Frequency Band: 2.402GHz – 2.480GHz
- RF Power Output: 13 dBm (EIRP)
- There is no restriction of use.
- Input: 5V=200mA (Earbuds) 5V=1A (Charging Case)
FCC Regulatory Compliance
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
ISED Regulatory compliance
This device contains licence-exempt transmitters that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
ISED Regulatory compliance
This device contains licence-exempt transmitters that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
This device may not cause interference. This device must accept any
interference, including interference that may cause undesired operation of the
device. This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment.
For more information, please visit our website:
FB: @hecateglobal
INSTA: @hecate_global
Model: EDF700035
FCC ID: Z9G-EDF194
IC: 10004A-EDF194
Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong
www.edifier.com
© 2022 Edifier International Limited. All rights reserved.
Printed in China
www.hecategaming.com
Designed by DONGGUAN EDIFIER ESPORTS TECHNOLOGY CO.,LTD.
NOTICE:
For the need of technical improvement and system upgrade, information
contained herein may be subject to change from time to time without
prior notice.
Products of EDIFIER will be customized for different applications. Pictures and illustrations shown on this manual may be slightly different from actual product. If any difference is found, the actual product prevails.
Hereby, Edifier International Limited declares that the radio equipment type EDF700035 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.edifier.com/int/eu-doc.html
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>