Anhui Yuwei YWSA-1200W Portαble Power Instruction Manual

Portαble Power
Stαtion Manual 

PRODUCT SPECIFICATION

Please read the instruction manual carefully before use

WARNING
Children aged 3 cannot operate alone

Product Display Diagram

Short brief

This is a portable power station for outdoors and indoors. Apply to wild camping, emergency communication, medical emergency, long drive journey, outdoor fishing. Can supply 600W power for your devices.

Parameter

current, short-voltage
LED screen| Show battery charging status| Percentage of battery. Charging status
DC. AC, PD Working condition| Showing watt
Battery pack| Type| Lithium iron phosphate 32135 15000MA
Capacity| 30000mAH 6S4P
Battery pack watt| 1152Wh
Recycle| Over 1 000 times
Over-heat Protection| AC over-heat Protection| ≥ 85℃
Battery over-heat Protection| ≥  65℃
Boot static| <1W

Product using time (Discharge)

• as different brand devices. The discharging time is also different. Please subject to realitγ.

Product size

Panel

The manual of USB QC3.0 and PD output

1. Long press 3 seconds of turn on/off switch to turn on the devices. LCD screen will turned on.
2. Long press 3 seconds of USS switch. USS icon will show on LCD screen. Which means its ready.
3. Plug in devices. Stαrt to discharge.
4. When finish using. Please pull off the plug. The whole device will shut down automaticallγ．

The manual of AC 220V/600W output

1. Long press 3 seconds of turn on/off switch to turn on the devices. LCD screen will turned on.

2. Long press 3 seconds of AC switch. AC icon will show onLCD screen. Which means its ready.

3. Plug in devices. Start to discharge.
   (Before charging the device, please check whether the power of the device exceeds é600W, and the energy storage power only supports devices ≤ 600W)

4. When finish using. Please pull off the plug. The whole device will shut down automatically

The manual of DC5521 output

1. Long press 3 seconds of turn on/off switch to turn on the devices. LCD screen will turned on.
2. Long press 3 seconds of DC switch. DC icon will show onLCD screen. Which means its ready.
3. Plug in devices. Start to discharge.
4. When finish using. Please pull off the plug. The whole device will shut down automatically.

The manual of wireless charging output

1. Long press 3 seconds of turn on/off switch to turn on the devices. Wireless charging automatically turned on.
2. Put the smartphone on the wireless charging panel.
   Start wireless charging.

Warning

1. Don’t put device into water.
2. Don’t heating the device or near fire source.
3. Don’t tear apart device.
4. Don’t over-hit the product or throw from high level.

Attention

1. Please follow the manuals.
2. Please leave at least 5cm for the air vent. In case the device over-heating.
3. The device will automatically shut off when the electricity of device is not enough or the discharging device watt is bigger than 500W, orin high temperature condition.
4. Please don’t charge and discharge at same time.
5. If you don’t use this device for a long time. The electricity may runs out. Please charge this device every 6 months.
6. When loading some big watt products. If its\ instantaneous power is over 1000W. the device will automatically protect itself. It will turn off the output. Please make sure the loading product need no more than 1000W of instantaneous power.
7. Please don’t use this device under some extremely condition, eg: flammable or corrosive condition.
8. If you drop the device into water by accident.
   Please send back it to where you purchased.
   We will take care if. If the device damaged by wrong use. We may charge accordingly.

FCC statement:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of device a distance of 15 cm  surrounding the device and 20 cm above the top surface of thedevicemust be respect ed.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>