kogan com KACLIPOEBLK Clip-On Earphones User Guide

User Guide CLIP-ON EARPHONES
KACLIPOEBLK

SAFETY & WARNINGS

User Safety Instructions

• To avoid any possible hearing damage, keep the volume at a moderate level.
• Avoid listening to music at loud volume levels for prolonged periods of time, as this may cause permanent hearing damage or hearing loss.
• Always be aware of your surroundings while operating and do not use the earphones while driving, cycling, running or jogging or when doing any activity which requires your attention and ability to hear.
• Even if not using, charge the earphones and the battery case at least once every 6 months, for the good life cycle of the product.
• Store in cool and dry place. Keep away from hot and humid conditions.
• The battery is designed to last lifecycle of the product. It should only be removed by a recycling facility. And attempt to remove or replace the batteries will damage the product and void the warranty.
• Bluetooth products can be affected by the environment. Do not use it in environments with large electromagnetic fields / high radiation levels. The Bluetooth signal will be impacted and less than optimal performance may occur.
• Do not use these headphones in temperatures below 0°C or above 45°C.
• Do not use equipment in the thunderstorm weather. Thunderstorms may cause abnormal equipment operation and increase the risk of electric shock.
• Do not place the Bluetooth earphones in water or apply excessive force on it those may cause damage to the earphones, resulting in poor sound quality.

WARNING: The product contains a built-in lithium battery. To avoid the explosion, do not expose it to strong sunlight, sources of heat it or throw it into fire.

COMPONENTS

• Earphone (pair)
• Charging Case
• USB-C Charging Cable
• User Guide

OVERVIEW

1. Indicator
2. Button
3. Sound vent
4. Earbud charging point
5. Charging pin (in case)
6. Display
7. Charging port
8. L. headphone battery level
9. R. headphone battery level
10. Case battery level

OPERATION

For a better sound quality, it is recommended to use these headphones with iOS 8.0/ Android 4.3 or above operating system.
Power On

• Press & hold the button on the headphone for 5 seconds.

• The headphones will automatically power on after removing the headphones from the charging case.
  Power Off

• Put the earbuds into the charging case, to power off earbuds and charging earbuds.

• The headphones will automatically power off, after 3 minutes when being disconnected from the paired device.
  Pairing

• Remove the headphones out of the case and the earbuds will power on automatically and enter the pairing mode. The headphones will play an audio prompt.

• Turn on Bluetooth on your phone and search the pairing name “Kogan Clip on Earphones” and tap to connect manually.
  Note: The headphones will reconnect the last pairing device auto next time they are turned on.

Tips:

• During pairing, the master headphone indicator flashes red and blue alternately and the slave headphone indicator will be off.
• Both L/R earbuds can be used separately.

How to Wear
Place the headphone in your ears and twist them slightly until they sit comfortably and stably. Button Functions

| Status| Command| Function
---|---|---|---
On| Triple-click| Smart voice assistant
Incoming call| Click| Answer call
Double-click| Reject call/End call
Music| Click| Play/Pause
Double-click (Left earbud)| Previous song
Double-click (Right earbud)| Next song
Press and hold for 2s (Left earbud)| Volume –
Press and hold for 2s (Right earbud)| Volume +

Tip:

• To adjust the volume, continue holding the button until reach your desire volume, before releasing your hand.

Charging the headphones

Place the headphones into the charging case, the headphones will automatically start charging.

•  Charging: The indicator will be solid red and display will show the battery level.
• Full charged: Indicator on the headphones will turn off.
  Note: Earbuds take approximately 1.5 hours to be fully charged.

Charge the Charging Box
Plug the USB-C charging cable into the USB-C port in the charging case. Connect the other end of the charging cable to a DC5V/1A power source (phone charger). The display of the charging case shows the battery level from 1 to 100% until it is fully charged.
When the screen displays the “100”, disconnect the charging case and adapter.

SPECIFICATIONS

Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com
Kagon.com

References

• Kogan Help Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>