ARRMA 4×4 4S BLX Vehicle Instruction Manual

ARRMA 4×4 4S BLX Vehicle

Product Information

Specifications

• Product : ARRMA 4×4 4S BLX Vehicle
• Transmitter : SPEKTRUM SLT3
• Batteries : AA Batteries x4
• Required : LiPo Battery (2x2S, 1x3S or 1x4S), LiPo Charger
• Website: www.arrma-rc.com

Product Usage Instructions

Warnings
Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property, and cause serious injury. Age Recommendation: Not for children under 14 years. This is not a toy.

Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others. This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

Water-Resistant Vehicle with Waterproof Electronics
Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many wet conditions, including puddles, creeks, wet grass, snow, and even rain. While the entire vehicle is highly water- resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s), and receiver are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.

CAUTION : Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.

General Precautions
When operating the vehicle in wet conditions, follow these general precautions:

• Do not submerge the vehicle in water.
• Avoid driving through deep puddles or bodies of water.
• After driving in wet conditions, inspect the vehicle for any water ingress and dry it thoroughly before storing or using it again.

Maintenance
After driving in wet conditions, follow these maintenance guidelines:

• Do not use a pressure washer to clean your vehicle as it can damage the components.
• Instead, use a damp cloth or sponge to wipe down the vehicle and remove any dirt or debris.
• Dry the vehicle thoroughly before storing it to prevent corrosion.

FAQ

Where can I find up-to-date product literature?
You can find up-to-date product literature on the websites www.horizonhobby.com or www.towerhobbies.com. Click on the support or resources tab for this product.

Can children under 14 years use this product?
No, this product is not for children under 14 years. It is not a toy.

Is the vehicle completely waterproof?
No, while the vehicle is highly water-resistant, it is not completely waterproof. The electronic components are waterproof, but most of the mechanical components are only water-resistant and should not be submerged.

How should I clean the vehicle after driving in wet conditions?
Do not use a pressure washer. Instead, use a damp cloth or sponge to wipe down the vehicle and remove any dirt or debris. Dry the vehicle thoroughly before storing it to prevent corrosion.

WHAT’S INCLUDED?

Warnings

NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product.

MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING : Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION : Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE : Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

WARNING : Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible compo-nents or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy. As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others. This model is controlled by a radio signal subject to interfer-ence from many sources outside your control. This interfer-ence can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as the motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously by touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.
• Always turn on your transmitter before you turn on the car. Always turn off the car before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of the radio equipment.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain. While the entire vehicle is highly water-resistant, it is not com-pletely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is  not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.

CAUTION : Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.

General Precautions

• Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Caution should be taken when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your transmitter’s manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.
• Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.

Wet Conditions Maintenance

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.

NOTICE : Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil or lubricant. Do not spray the motor.
• Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and re-oil the bearings with lightweight motor oil.
• Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed.

Support
At ARRMA we want you to love running your kit and make owning a high performance RC car as simple as pos- sible. If you have any questions about running, maintaining, tuning or repairing your ARRMA product there are three options for you to use to get help and advice. Visit ARRMA-RC.com for support, parts and upgrades for your kit. If you can’t find what you’re looking for then you can always email us at support USA @ARRMA-RC (USA) or support@ARRMA-RC.com (ROW) 24hrs a day and we will do our best to help you with your query.

Quick Start Guide

Install AA Batteries In Controller

CAUTION : Only charge rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION : Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

Remove Body

Install Charged Batteries In Car

Connect ESC and Power On

• CONTROLLER ON FIRST
• CAR ON SECOND

How to Drive

Steering Neutral

Install Car Body

NOW GET SHREDDING!

Power Off

• CAR OFF FIRST
• CONTROLLER OFF SECOND

Storage
ALL SAFE… UNTIL NEXT TIME!

Electronic Speed Controller (ESC)

ESC Specifications

• Input Voltage: 3S-4S LiPo (11.1-14.8v) 35C 5000mAh Minimum Req.
• BEC Output: 7.4v/4A Max

**Throttle  Setup

**

Connect batteries, turn on TX and press/hold the set button ‘A’. Turn the switch on ‘B’ and release the set button when the RED light flashes on the ESC.

1. TX in neutral – press set button (1 Green flash)
2. TX full throttle – press set button (2 Green flashes)
3. TX full brake – press set button (3 Green flashes)
4. Switch off ESC to complete setup

Battery Modes

Temperature Protection
If the ESC temperature exceeds 125 degrees Celsius/257 degrees Fahrenheit, the ESC will enter temperature protection mode and the green status LED will blink. Once the ESC has cooled down it will resume normal operation after it has been turned off and back on again.

ESC Tuning Options
The brushless ESC is setup for use straight from the factory, if you want to alter the settings for your track or driving style please see the table and steps below:

To alter ESC settings
3* Higher level means your battery will cut off at a higher Voltage. This protects your batteries. Run Time will be reduced the higher the level setting.

Factory Reset
To reset the ESC to factory default settings, connect a battery, turn the transmitter on and then turn the car on. Press and hold the set button for 5 seconds and release. The Red and Green lights will flash simultaneously to show you have reset. Switch the ESC off and factory reset is complete.

ESC LED INDICATOR

ESC turned On, LED

indicator is Off

| Throttle trigger is in the neutral zone
Red LED illuminated| ESC is operating in forward throttle
Red and Green LED illuminated| ESC is at full throttle, full brake or full reverse
LED flashes red with

short single pulses

| LVC protection activated
LED flashes green with

short single pulses

| The ESC is in thermal

shutoff mode

LED flashes green with three

short pulses repeating

| The ESC has exceeded the continuous current limit
LED flashes green with four

short pulses repeating

| The ESC has failed the self test
LED flashes green with five

short pulses repeating

| Capacitor temp has been exceeded

LVC Activation
When the battery voltage drops low enough to activate the LVC saftey feature the ESC will sound a double beep when using Spektrum SMART batteries. A single beep will be heard if using regular batteries.

TROUBLESHOOTING GUIDE

Problem and LED Indi- cator| Error Mode| Possible Causes| Solution
---|---|---|---
Motor won’t operate. LED flashes red with short single pulses.| LVC has been activated.| Battery voltage is below the LVC setting.| ****

Verify the battery is charged.

Motor won’t operate. LED flashes green with short single pulses.| The ESC is in thermal shutoff mode.| ****

The ESC is taking too much load.

| Turn off the ESC and allow it to cool before resuming operation. Consider making changes to gear ratio to reduce load to the ESC.
Motor won’t operate. LED flashes green with four short pulses repeating.| The ESC has failed the self test.| ****

The ESC is damaged.

| Send the ESC to a Horizon Hobby service center for service.
Motor won’t operate. LED flashes green with five short pulses repeating.| Capacitor temp has been exceeded| There is too much load on the drive system for the ESC to support.| Consider changing the battery or gearing to reduce the load on the ESC, or change your driving habits to reduce the load.
No throttle or steering on start up. LED flashes red with single short pulse repeating.| ****

N/A

| ****

Throttle trim not at neutral.

| Turn off ESC. Adjust throttle trim on transmitter to neutral. Turn back on.

Radio Gear

Factory Defaults

SR315 Binding SLT Protocol (Included)

• Connect a fully charged battery pack to the ESC.
• Power on the ESC. press the bind button three times quickly (within 1.5 seconds of the first button press).
• Set the trims and control positions at the desired failsafe settings, and power ON the SLT3 transmitter.

SR315 Binding DSMR Protocol (Not Included)

• Connect a fully charged battery pack to the ESC.
• Press and hold the bind button on the receiver. Power on the receiver. The orange LED flashes, indicating the receiver is in bind mode. Release the bind button after the orange LED illuminates.
• Put your DSMR transmitter (not included) in bind mode. The bind process is complete when the orange LED on the receiver remains lit.

FCC ID: BRWSPMSLT300 and FCC ID : BRWSRIRVINGV1
This equipment complies with FCC and IC radiation exposure limits set forth for an uncon-trolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and/or antenna and your body (excluding fingers, hands, wrists, ankles and feet). This transmitter must not be co-located or operating in conjunction with any other antenna or trans-mitter.

Supplier’s Declaration of Conformity
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC 2904 Research Road, Champaign, IL 61822
Email: compliance@horizonhobby.com Web: HorizonHobby.com 

Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: European Union Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EU; RoHS 3 Directive – Amending 2011/65/EU Annex II 2015/863; European Radio Equipment Directive (RED) 2014/53/EU The full text of the EU declaration of conformity is available at the following internet address: http://www.horizonhobby.com/content/support-render-compliance.

Wireless frequency range and wireless output power:

Transmitter:

• Frequency Band: 2402.0-2478.0 MHz
• Max EIRP : 16.6 dBm

Receiver:

• Frequency Band: 2402.0-2478.0 MHz
• Max EIRP : -1.33 dBm

Industry Canada Notice : IC: 6157A-SPMSLT300 and IC: 6157A-SRIRVINGV1 CAN ICES-3 (B)/NMB-3(B)

This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).

Operation is subject to the following 2 conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

Troubleshooting

Vehicle does not move

| ****

Batteries are incorrectly installed in transmitter

| Check Indicator Light on transmitter, see page 20
Weak, damaged or no drive battery in model| Install fresh, charged batteries

Frayed or broken motor or ESC wires

| Check condition, reconnect and insulate

ESC has shut down due to overheating

| Stop driving and allow ESC or motor to cool down

Electric motor is damaged

| Replace with new unit – visit
ARRMA-RC.com for advice and upgrades!

Waterproof ESC is damaged

| Replace with new unit – visit
ARRMA-RC.com for advice and upgrades!

Possible damage to transmission/drive-line

| Check components and replace – visit ARRMA-RC.com for advice
ESC low voltage cutoff has activated to protect

batteries

| Remove drive battery, leave to cool down if necessary, and re-charge
Vehicle does not reverse| ****

Running mode is set to Fwd/Brk

| Retune ESC Running Mode to ‘Fwd/ Brk/Rev, see page 18

Vehicle drives without input

| ****

Transmitter throttle trim incorrectly set

| Throttle trim needs to be set to zero/ neutral – see page 21 for factory defaults
Neutral throttle position of ESC Unit incorrect| Re calibrate the ESC

Short runtime

| Battery damaged or not fully charged| Check condition, replace or recharge

Electric motor dirty or damaged

| Clean, check condition and/or replace

– visit ARRMA-RC.com for more information

Incorrect ESC battery mode – voltage cutoff too high

for the battery you are using

| ****

Adjust the battery mode of the unit

Sluggish performance

| Battery damaged or not fully charged| Check condition, replace or recharge

Transmitter throttle trim incorrectly set

| Throttle trim needs to be set to zero/ neutral – see page 21 for factory defaults

Electric motor dirty or damaged

| Clean, check condition and/or replace

– visit ARRMA-RC.com for more information

Drivetrain dirty or damaged

| Clean, check condition and/or replace

– visit ARRMA-RC.com for more information

No control of vehicle or short range

|

Transmitter batteries are weak or fitted incorrectly

| Check Indicator Light on transmitter, see page 20
---|---|---
Servo wires to receiver loose or connected incor- rectly|

Reinstall servo wires to receiver

Transmitter and receiver unit are not ‘bound’ cor- rectly| Transmitter and receiver need to be bound – see page 21

Steering/Throttle operation intermittent

|

ESC has shut down due to overheating

| Stop driving and allow ESC or motor to cool down

Transmitter and receiver unit are not ‘bound’ cor- rectly

| Check for sources of interference and re-bind transmitter/receiver – see page 21

Vehicle wanders left/right without steering input

| Steering trim setting out| Adjust steering trim – see page 21

Damaged steering components

| Check components and replace – visit ARRMA-RC.com for advice

Drivetrain dirty or damaged

| Clean, check condition and/or replace

– visit ARRMA-RC.com for more information

Steering/Throttle operation Reversed

|

Relevant channel of transmitter is reversed

| Reverse relevant channel on trans- mitter – see see page 21 for factory defaults

Check that the wires from the ESC to the motor are connected correctly

| Reconnect in the correct orientation (orange to orange, yellow to yellow and blue to blue) ensuring fit is tight; if not pinch female connector with pliers

Limited steering angle

|

Transmitter steering dual-rate set incorrectly

| Adjust transmitter dual-rate – see page 21 for factory defaults

Damaged steering components

| Check components and replace – visit ARRMA-RC.com for advice

Warranty Information

LIMITED WARRANTY

What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 2 years from the date of purchase.

What is Not Covered
This warranty is not transferable and does not cover

1. osmetic damage,
2. damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance,
3. modification of or to any part of the Product,
4. attempted service by anyone other than a Horizon Hobby authorized service center,
5. product not purchased from an authorized Horizon dealer,
6. Product not compliant with applicable technical regulations, or
7. use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon.  Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no

event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law
These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.

Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/service-center render- service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

NOTICE : Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.

Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the
sole discretion of Horizon.

Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website
http://www.horizonhobby.com/content/_service-center_render-service-center.

ATTENTION : Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.

JOIN OUR GLOBAL ARRMA COMMUNITY

ARB100047279
ARRMA-RC.COM
©2023 Horizon Hobby, LLC. ARRMA RC is a trade name of Horizon Hobby Ltd. Horizon Hobby Ltd is a subsidiary of Horizon Hobby, LLC. ARRMA, the ARRMA logo, Kraton and Outcast are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks and logos are property of their respective owners.

References

• ARRMA RC Cars and RC Trucks - Designed Fast, Designed Tough | ARRMA
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• Ferngesteuerte Flugmodelle, Autos, Trucks, Hubschrauber, Boote und Fernsteuerungen | Horizon Hobby
• ARRMA RC Cars and RC Trucks - Designed Fast, Designed Tough | ARRMA
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• RC Cars, RC Trucks, RC Airplanes, Model Trains, and Slot Cars at Tower Hobbies

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>