Qbic Technology HC-0850N-PW Luminen 8 Touch Panel PC User Guide

: June 9, 2024
: Qbic Technology

Table of Contents

Contents
Indication
Installation
LASER SAFETY
CARE AND WARNING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Qbic Technology HC-0850N-PW Luminen 8 Touch Panel PC

Indication

Display
Mic
Sensors
Home Button
Reset Button
Speaker
Light Bar
RJ45 / POE
DC 12V
USB Micro-AB
Restore Button
Camera

Installation

STEP 1
Fasten M3.2 screw *2 to secure the bracket to gang box.
STEP 2
Mount the Panel PC on the bracket.
STEP 3
Fasten M2.5 screw *1 to secure the Panel PC to bracket

CAUTION: This product is only suitable for installations less than or equal to 2m(6.56ft) high for CE/UL safety.

LASER SAFETY

This product complies with FDA performance standards for laser products except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019.
Date of manufacture: the date code shown on the product label represents the manufacturing date of this laser product.
LASER SAFETY

CAUTION: Invisible laser radiation when open. Avoid exposure to beam. Class 1 laser product. This system must be opened only by qualified technicians to prevent accidents caused by the laser beam.

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

The ambient light sensor can automatically adjust panel brightness base on the environment. See Display Settings to enable automatic brightness.

The Laser proximity sensor will detec nearby motion to wake the panel up without requiring a touch.

CARE AND WARNING

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/panel PC technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

May not cause harmful interference.
Must accept any interference received, including interference that may cause undesired operation.

Correct disposal of this product :
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

The power consumption of the product in networked standby is 3.3W which all wired network ports are connected and all wireless network ports are activated.
The product is to be connected only to PoE networks without routing to the outside plant.

FCC & CE RF radiation Exposure Statement Caution :
To maintain compliance with the FCC & CE`s RF exposure guidelines. Place the product at least 20cm from nearby persons.

Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types); Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

This unit is intended to be supplied by an UL / IEC 62368-1 certified Class II power adapter suitable for use at minimum 40 degree C and altitude of operation up to 5,000 m whose output complied with LPS/PS2 and meets ES1, and is rated 12 V d.c., minimum 1.5 A or UL/IEC 62368-1 certified PoE output power supply suitable for use at minimum 40 degree C and altitude of operation up to 5,000 m whose output complied with LPS/PS2 and meets ES1 and is rated 44-57 V d.c., minimum 0.4 A

Canada, Industry Canada (IC) Notices
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.

This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body).

CAUTION
Risk of explosion if the battery is replaced by an incorrect type. Wait one- half hour after switching off before handling parts

Power information: Input: PoE 44V – 54V 0.3A
Power adapter information:
Input: 100-240V~50/60Hz 0.5A
Output: 12V 1.0A
NOTE : Operating Temperature: 0°~ 40°C