QBIC TECHNOLOGY EP-0700 E-Paper Panel PC User Guide

: June 15, 2024
: Qbic Technology

Table of Contents

QBIC TECHNOLOGY EP-0700 E-Paper Panel PC
Product Information
Contents
Product Overview
Installation
CARE AND WARNING
About device information
General Procedure
SPECIFICATION
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

QBIC TECHNOLOGY EP-0700 E-Paper Panel PC

Product Information

Specifications
- Model: EP-0700
- Type: ePaper
Product Overview
- The EP-0700 is a versatile ePaper display designed to provide clear and readable information. It comes with various mounting options for easy installation.
Package Contents
- EP-0700
- Bracket (Optional)
- I/O Cover
- Tape (Optional)
- M3x4 screw *2 (For battery cover)
- M3x6 screw *3 (For Bracket)
Installation
- Step 1: Install Battery
- Open the battery cover.
- Insert up to 6 CR2450 coin batteries into the battery compartment.
- Secure the battery cover using the provided M3x4 screws.
- Step 2: Tape Mount
- Attach the tape to the back of the bracket.
- Position the bracket on the desired surface.
- Secure the bracket and ePaper together using the provided M3x6 screws.
- Step 3: Surface Mount
- Install the bracket on a suitable surface such as wood or concrete (screws not included).
- Mount the ePaper display onto the bracket.
- Secure the bracket and ePaper together using the provided M3x6 screws.
- NOTICE: It is recommended to use M3 screws to secure the bracket and ePaper. The suggested length of the M3 screw should be the thickness of the mounting bracket plus 8mm (screws not included). Before using the tape, make sure the mounting surface is clean and smooth. Apply appropriate torque to the M3 screws.
FAQ
- Q: How many batteries does the EP-0700 support?
- A: The EP-0700 supports up to 6 CR2450 coin batteries.
- Q: Are the mounting screws included in the package?
- A: Yes, the package includes M3x4 screws for the battery cover and M3x6 screws for the bracket.
- Q: Can I mount the ePaper display on concrete?
- A: Yes, you can mount the ePaper display on concrete. However, please note that the screws for surface mounting are not included in the package.

Product Overview

$QBIC-TECHNOLOGY-EP-0700-E-Paper-Panel-PC-FIG-1 $2$$

Display
LED
Button 1
Button 2
Button 3
Reset
Bracket
Battery Cover

Installation

Install Battery

```
*  **STEP 1**  
```
Install CR2450 coin batteries. (up to 6 pcs)
- STEP 2
  Fix M3 screws to the battery cover. $QBIC-TECHNOLOGY-EP-0700-E-Paper-Panel-PC- FIG-1 $3$$

Tape Mount

STEP 1
Attach tape on the back of the bracket.
STEP 2
Fix the bracket with tape on the surface.
STEP 3
Fasten M3 screw*3 to secure the bracket and ePaper. $QBIC-TECHNOLOGY-EP-0700-E -Paper-Panel-PC-FIG-1 $4$$

Surface Mount

STEP 1
Install a bracket on the surface. (wood/ concrete) (screws not included)
STEP 2
Mount the ePaper on the bracket.
STEP 3
Fasten M3 screw*3 to secure the bracket and ePaper. $QBIC-TECHNOLOGY-EP-0700-E -Paper-Panel-PC-FIG-1 $5$$

NOTICE:

It is recommended to secure with M3 screw. The suggested length of the M3 screw is the thickness of the mounting bracket plus 8mm(screw not included).
Please ensure the mounting surface is clean and smooth before using the tape.
M3 screw Torque<2 kgf-cm
Recommended Installation Height: <2M

CARE AND WARNING

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used by the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/panel PC technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

May not cause harmful interference.
Must accept any interference received, including interference that may cause undesired operation.

Correct disposal of this product:

This marking indicates that this product should not be disposed of with other household wastes
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used device, use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

FCC & CE RF radiation Exposure Statement Caution:

Place the product at least 20cm from nearby persons.

Replacement of a battery with an incorrect type that can defeat a safeguard

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
Leaving a battery in an extremely high-temperature surrounding environment can result in an explosion flammable liquid or gas; flammable liquid or gas.

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless
The device should be used in such a manner that the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body).
Informations concernant l’exposition aux fréquences radio (RF)

About device information

You can press the top and middle buttons at the same time to get label information.

FCC ID: 2AF82-EP0700
IC: 23322-EP0700
HVIN: EP0700

Surface Preparation for Tape Application

Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA) and water* before applying Tapes. There are exceptions!

Exceptions to this general procedure that may require additional surface preparation include:

Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or greasérom a surface and should be followed by cleaning with IPA/water.
Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt oxidation and can increase surface area to improve adhesion.
Porous Surfaces: Most porous and fibered materials such as wood, particleboard, concrete, etc need to be sealed to provide a unified surface.
Unique Materials: Special surface preparation may be needed for glass and glass-like materials, copper and copper containing metals and plastics, or rubber that contains components that are figurate (e.g. plasticizers).

General Procedure

To obtain optimum adhesion, the bonding surfaces must be well unified, clean, and dry.
Typical surface cleaning solvents are IPA/ water mixture (rubbing alcohol) or heptane. (Steps A and B)
Bond strength is dependent upon the amount of adhesive-to-surface contact developed.
Firm application pressure develops better adhesive contact and helps improve bond strength. (Steps C and D) Generally, this means that the tape should experience at least 15 ps(100 kPa) in roll-down or platen pressure.
After application, the bond strength will increase as the adhesive flows onto the surface. At room temperature, approximately 50% of the ultimate strength will be achieved after 20 minutes, 90% fter 24 hours, and 100% after 72 hours.
In some cases, bond strength can be increased and ultimate bond strength can be achieved more quickly by exposure of the bond to elevated temperatures. (e.g. 1500F [660C] for 1 hour). $QBIC-TECHNOLOGY-EP-0700-E-Paper-Panel-PC-FIG-1 $6$$

NOTE: These cleaner solutions contain greater than 250 g/l of volatile organic compounds (VOC).

Please consult your local Air Quality Regulations to be sure the cleaner is compliant.
When using solvents, be sure to follow the manufacturer’s precautions and directions for use when handling such materials.
The product contains a coin/button cell battery.
Do not ingest battery, Chemical Burn Hazard.
Keep batteries out of reach of children.