MOUNTUP MU0004 Single Monitor Desk Mount Instruction Manual
- June 15, 2024
- MOUNTUP
Table of Contents
MOUNTUP MU0004 Single Monitor Desk Mount
Product Information
- Specifications:
- Model: 80002-MA11-12-US7.0
- Compatible VESA sizes: 75x75mm, 100x100mm
- Weight capacity: 4.4~17.6 lbs (2~8 kg)
Product Usage Instructions
- Package Contents:
- A (x1) Upper Arm
- A1 (x1) Cable Cover
- B (x1) Lower Arm
- C (x1) Base
- D (x1) Clamp
- E1(x1) Pad
- E2(x1) Pad
- F (x1) Wingnut
- G (x1) Carriage Bolt
- D1 Bracket
- D2 Bolt Y
- D3 Bolt Clip Plate
- H (x1) 3mm Allen Key
- I (x1) 5mm Allen Key
- J (x1) 6mm Allen Key
- K (x2) Bolt M6x8mm
- M-A (x4) M4x12mm
- M-B (x4) M4x25mm
- M-C (x8) Spacer H5mm
- M-D (x2) M6x8mm (Spare)
- Assembly Steps:
- Step 1: Apply Pads to the Base Bottom
-
* Apply pads (E1&E2) to the base bottom to avoid desk scratches.
-
- Step 2: Clamp Installation or Grommet Base Installation
- Option A: Clamp Installation
- Remove the plastic cover from Base (C).
- Mount Clamp (D) to the bottom of Base (C) by tightening bolts (K) with 5mm Allen Key (I).
- Adjust the Clamp width to fit your desk.
- Secure the stand to the desktop by tightening the clamp (D).
- Fix the plastic cover to Base (C).
- Option B: Grommet Base Installation
- If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.
- Detach Bracket (D1) from Clamp (D).
- Remove the plastic cover from Base (C).
- Run Carriage Bolt(G) through Base (C).
- Tighten Wingnut (F) after making Bracket (D1) through Carriage Bolt (G) and stack above Wingnut (F), Base (C) will be fixed to your desk securely.
- Install the plastic cover to Base (C) finally.
- Step 3: Arm Installation
- Install the lower arm (B) to the base (C).
- Attach upper arm (A) to the lower arm (B).
- Secure the arm by tightening the inside screw using a 3mm Allen key (H).
- Important Note:
- If the VESA plate is crooked, please hold it with both hands and rotate vigorously to make up arrows pointing up.
- Do not tighten the screw excessively or it might be stripped.
- If the inside screws are stripped, you can use M-D spare screws. If the inside screws are missing, you can use M-D spare screws.
- Frequently Asked Questions (FAQ)
- Q: What are the compatible VESA sizes for this desk mount?
- A: This desk mount is compatible with VESA sizes 75x75mm and 100x100mm.
- Q: What is the weight capacity of this desk mount?
- A: The weight capacity of this desk mount is 4.4~17.6 lbs (2~8 kg).
- Q: Can I use this desk mount for monitors over its load capacity?
- A: No, using the product for monitors over its load capacity may cause damage or serious injury. Please do not exceed the weight capacity.
- Q: Are all the hardware included in the package necessary for installation?
- A: Not all hardware included will be used for installation. Please refer to the assembly steps for the required hardware.
- Q: Are there any safety precautions I should be aware of?
- A: Yes, please keep the small items included in the kit out of reach of children under 3 years old as they could be choking hazards if swallowed. Adult supervision is required.
WARNING!
- If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help.
- Before assembly, please check and make sure all necessary accessories are included and undamaged.
- Improper installation, such as the use of the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury.
- We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
- The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF THE REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
ASSEMBLY STEPS
Warm Tips You could also refer to the Video Guide about installation on our product page.
- STEP 1: Apply Pads to the Base Bottom
- STEP 2: Clamp Installation or Grommet Base Installation
- OPTION A: Clamp Installation
- Remove the plastic cover from Base (C).
- Mount Clamp (D) to the bottom of Base (C) by tightening bolts (K) with 5mm Allen Key (I).
- Adjust the Clamp width to your desk.
- Secure the stand to the desktop by tightening the clamp (D). Fix the plastic cover to Base (C).
- STEP 2: (Continued)
- OPTION B: Grommet Base Installation
- If the existing grommet hole comes with a plastic protector, remove it to ensure a surface before installing the desk mount.
- Firstly detach Bracket (D1) from Clamp (D).
- Then remove the plastic cover from Base (C). Run Carriage Bolt(G) through Base (C).
- By tightening Wingnut (F) after making Bracket (D1) through Carriage Bolt (G) and stacking above Wingnut (F),
- Base (C) would be fixed to your desk securely. Install the plastic cover to Base (C) nally.
- STEP 3: Arm Installation
- Install the lower arm (B) to the base (C). Attach upper arm (A) to the lower arm (B). Secure the arm by tightening the inside screw using 3mm Allen key (H).
- Note: If the VESA plate is crooked, please hold it with both hands and rotate vigorously to make up arrows pointing up.
- STEP 4: Attach Monitor
- STEP 5: Tilt Adjustment
- Problem: Monitor tilts down.
- Solution:
- Loosen the tilting bolt.
- Hold the bottom of the monitor with one hand and adjust to determine your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle.
- Problem: Monitor tilts down.
- STEP 6: Adjust Tension
- The gas spring is pre-set to medium tension. For intended functioning of the mount, you will need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J).
- NOTE: If the bolt is covered over, please hold the upper arm and press it down to maintain a horizontal position, and then you can see the adjustment screw at the joint. Be sure to keep the arm in a horizontal position during adjustment.
- Situation 1: Arm falls down Upper Arm with monitor falls and fails to stay where intended.
- Solution: Turn the inside screw counterclockwise(“+” direction) to increase gas spring tension until the arm can stay as intended.
- Situation 2: Arm rises or can’t press down Upper Arm with monitor rises and fails to stay where intended.
- Solution: Turn the inside screw clockwise(“-” direction) to decrease gas spring tension until the arm can stay as intended.
- The gas spring is pre-set to medium tension. For intended functioning of the mount, you will need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J).
- STEP 7: C (aCbolnet Minauneadg) cement
- Remove Cable Cover
- For the lower arm: Remove the bottom plastic cover from the lower arm as shown in the diagram below.
- Attach Cable Cover
- For the upper arm: Run cables through the cable cover(A1), then with both hands slightly press inwards the tabs inside the cover and insert them into the upper arm.
- For the lower arm: Run cables through the cable cover, then insert and slide the cover down for reattachment.
Adjust as Desired
Adjust monitor position and rotation.
- Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
- Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
Product Dimensions
CAUTION AND MAINTENANCE
- Don’t allow children to climb, stand, hang, or play on any part of the monitor or stand.
- This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.
- Check if the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please feel free to contact Customer Service via Amazon before returning. 80002-MA11-12-US7.0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>