XTM 659215 12V 24V Control Box Instruction Manual

XTM 659215 12V 24V Control Box

DIMENSION

• The XTM 12V / 24V control box is the perfect pre-wired DIY solution to power most of your 12V / 24V accessories in one central location. Please read and understand all the instructions carefully before installation and operation.

FEATURES

• 12V / 24V CONTROL PANEL, PRE-WIRED SUITABLE FOR MOST 4WD, TRAILER OR CARAVAN APPLICATIONS
• FEATURES 2 X QUICK CONNECT PLUGS,
• 4 X ROCKER SWITCHES, 2 X USB PORTS, 2 X POWER SOCKETS,
• 8 X CIRCUIT BREAKERS, 1 X LED VOLTMETER & SWITCH
• 4 ROCKER SWITCHES THAT CAN BE WIRED UP TO POWER CAMP LIGHTS AND OTHER ACCESSORIES
• LASER-CUT BLACK POWDER-COATED ALUMINIUM MAKING IT LIGHTWEIGHT

SPECIFICATIONS

CIRCUIT BREAKER:

| 15A *2 FOR POWER SOCKETS

5A* 2 FOR USB PORTS / VOLTMETER

15A *4 FOR ROCKER SWITCHES

CIRCUIT BREAKER FOR QUICK CONNECT PLUG：| AUTOMATIC RESET, 50A2
OPERATING TEMPERATURE:| -5-45 ℃
BOX DIMENSIONS:| 250210*90MM
WEIGHT:| 1600G

SAFETY WARNINGS

• Keep children and pets away from the control box.
• Installation by a licensed auto electrician is recommended.
• Always use appropriate personal protective equipment when installing.
• Always disconnect any power source, eg car battery before commencing any electrical work, to ensure person and vehicle safety.
• Always use enough gauge wiring when installing the control box. If not sure, please use the recom-mended cable size or contact a qualified auto electrician for correct cable size.
• Do not insert any body parts or tooling into any components.
• Ensure all exposed wires are covered.
• Do not expose the control box to wet weather.
• Ensure input cables are fused appropriately. Please use the recommended fuse or contact a qualified auto electrician for correct fuse size. Correct soldering and shrink wrapping of all joints is recommended to avoid any short circuits.
• Provide as much ventilation as possible for the control box to decrease heat accumulation.

INSTALLATION INSTRUCTIONS

This control box can be mounted either vertically or horizontally and is designed to be flush mounted to a flat surface.

1. Unscrew the 4x flat head screws to open the cover plate by a hand screwdriver (not included). After opening the cover plate, make sure all wiring is properly connected and no internal terminal studs are loose.
2. Lift the control box onto the desired location, and mark the locations of the drilled mounting holes on the canopy wall. Remove the box and drill the holes accordingly.
3. Lift the control box onto the desired location and insert the mounting bolts (not included). Tighten the mounting fasteners using nylon nuts and washers (not included). It is recommended to use 4 x M5 screws (not included) to secure the control box. Large washers (not included) should be used on either side of the bolted joint to spread the load across a greater area to prevent failure or pull-through of the bolt.
4. Fasten the 4x flat head screws with a hand screwdriver (not included) to close the cover plate. Do not over-fasten the mounting screws.
5. Connect the positive and negative cables from the Auxiliary battery to the red and black studs in the box respectively. Connect the desired devices to be controlled to the switch load terminals in the back of the front panel as the wiring diagram below:

Once complete, the LED display on the voltmeter should be an indication of power going into the panel. If there is no power, check cabling, and wiring, test using a 12v multimeter, or contact a licensed auto electrician.

WARRANTY

Our product is guaranteed to be free from quality and manufacturing defects for 12 months. If your product becomes defective during this period, SRGS PTY LTD will offer you either a replacement, credit, or refund if a product is faulty; wrongly described; different from the sample shown to you, or does not do what they are supposed to do.

This warranty will not cover substantially modified products; misuse or abuse of the product contrary to user instructions or packaging label; change of mind and normal wear and tear.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and failure does not amount to a major failure.

To claim the warranty, take the product to the front Service Desk of your nearest store of purchase. You will need to show a receipt or other proof of purchase. Additional information may be required to process your claim. Should you not be able to provide proof of purchase with a receipt or bank statement, identification showing your name, address, and signature may be required to process your claim. Any expenses relating to the return of your product to the store will normally have to be paid by you. For online store purchases, SRGS PTY LTD will pay for the return freight for any product assessed as having a major failure.

The benefits to the customer given by this warranty are in addition to other rights and remedies of the Australian Consumer Law concerning the goods or services to which this warranty relates.
This warranty is provided by SRGS PTY LTD, 6 Coulthards Avenue, Strathpine QLD 4500, Australia. Phone: 1300 880 764.

FAQ

• Q: Can I use this control box for my car?
• A: Yes, the XTM 12V / 24V control box is suitable for most 4WD, trailer, or caravan applications.
• Q: How many circuit breakers does it have?
• A: The control box has 8 circuit breakers in total.
• Q: Can I mount the control box vertically?
• A: Yes, the control box can be mounted either vertically or horizontally.

PLU: 659215
CODE: DT22101911 Manufactured and packaged for SRGS PTY LTD
ABN 23 113 230 050 6 Coulthards Avenue, Strathpine QLD 4500, Australia MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>