IPEVO VOCAL HUB Wirelessly Vocal Speakerphones Installation Guide
- June 15, 2024
- IPEVO
Table of Contents
Wirelessly connect up to
6 IPEVO VOCAL Speakerphones
www.IPEVO.com
Knowing your IPEVO VOCAL HUB
Package Contents
-
Mode button
• Press once to switch connection modes
• Press and hold for 3 seconds to turn On/Off the VOCAL HUB -
Connection mode LED indicator
• Red: USB mode
• Blue: Bluetooth mode
• Off: Line IN / OUT mode -
Bluetooth pairing button and LED indicator
• Quick flash: Pairing
• Constantly On: Paired
• Slow flash: Not paired -
Audio input jack
-
Audio output jack
-
USB port
Start using the IPEVO VOCAL HUB Expanding the wireless conference space
Step 1
Please connect the power of the VOCAL HUB. Step 2
Press and hold the Bluetooth pairing button for 3 seconds to enter pairing
mode, and pair it with IPEVO VOCAL that is in Bluetooth pairing mode; the
indicator on VOCAL HUB will remain constantly On when paired successfully.
Please only pair with one IPEVO VOCAL at a *time. Remarks**
Press and hold the Bluetooth pairing button of the corresponding number for 10
seconds to clear and reset the Bluetooth settings.
Precaution
Do not use/store the product in the following environments:
- Near heat sources
- Sandy or dusty places
- Locations with high humidity
Step 3
Select the connection mode to use and connect with the user device to complete
the setting.
-
USB mode
Connect VOCAL HUB with the PC using the USB cable. -
Bluetooth mode
Connecting VOCAL HUB with supported Bluetooth connection devices such as PC, tablet and smartphone. -
Line IN / OUT mode
Use the 3.5mm audio cable to connect VOCAL HUB with a conference system that supports 3.5mm audio input/output.
For a full user manual, FAQ & tech support, visit www.ipevo.com/products
/vocal-hub/support
All trademarks, logos, and brands are the property of their respective owners
and are used for identification purposes only.
IPEVO VOCAL Instructions
- It is recommended to adjust the IPEVO VOCAL speaker volume to maximum, turn on the AI MIC, and use OMNI omni-directional reception mode.
- Press and hold the mute button on a single IPEVO VOCAL for 3 seconds to mute/ unmute all VOCALs connected to the IPEVO VOCAL HUB.
- Press the mute button on a single IPEVO VOCAL to mute/unmute a single IPEVO VOCAL.
Please refer to the IPEVO VOCAL instruction manual for details.
Notes
- This product needs to be used with the IPEVO VOCAL AI Beamforming Bluetooth Speakerphone for it to work.
- The maximum connection distance between IPEVO VOCAL HUB and VOCAL can reach up to 49 ft / 15 meters (there must be no large objects, such as walls, blocking in between).
- IPEVO VOCAL HUB can connect up to 6 VOCALs; if Bluetooth mode is used to connect to the user device, it is recommended to connect up to 4 VOCALs in order to achieve optimum usage effects.
- IPEVO VOCAL HUB has memory function and can pair automatically when switched on again. If previously paired IPEVO VOCALs cannot connect automatically, please repair such instance by following the instructions in Step 2.
- The optimal reception range for the IPEVO VOCAL is 5.9 ft (180 cm). It is advisable to position another VOCAL within 4.9 – 5.9 ft (150-180 cm), to prevent noise from each unit interfering with the other.
FCC Declaration
Federal Communications Commission (FCC) Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may
cause undesired operation of the device
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FCC ID: WKP-CDHB-01IP
IC: 23924-CDHB01IP
CAN ICES-003(B)/NMB-003(B)
201-230570
R-R-1PV-IPEVO_VOCALHUB
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>