SEBSON TREIBER_LED15 LED Driver User Guide

: June 15, 2024
: SEBSON

Table of Contents

TREIBER_LED15 LED Driver
General safety information:
Start up
Technical Data:
Cleaning:
Documents / Resources

TREIBER_LED15
TREIBER_LED20

TREIBER_LED15 LED Driver

Manual

Thank you for choosing a product of SEBSON. Read the instructions carefully and keep them for looking up before start-up this product. A long and failure- free operation can only be guaranteed if the installation and start-up is done properly. Before starting up this product, please check for external damage. In case of visible external damage we immediately dis-advise the start-up of this product! Please remove all packaging material of this product before the first start-up an and check the content for completeness!
Intended use:
This SEBSON brand LED driver is especially suitable for LED bulbs that are operated with 12V DC voltage.

General safety information:

Danger: The installation of this product may be done only by a qualified person according the valid regulations for electrical installation!
Danger: In case of damages or contact with water turn off this product immediately without tension and make sure that a restart is no longer possible!
Danger: Please keep this product away from children and animals!
Danger: Do not cover the device with heat-insulating materials! This is a fire hazard!
Caution: Avoid overloading the device, an overload can damage the device or cause a short circuit! Therefore, please note the maximum power consumption in the technical data! Consider a power reserve of at least 15%!

This device is only suitable for operating LED lamps or LED luminaires!
Do not connect a dimmer! The connection of a dimmer can lead to damage or functional impairment of the LED driver! The remodeling of this product is not allowed! The proper and safe functioning of the device can no longer be guaranteed if it is modified! In addition, this will invalidate the warranty claim!
The manufacture does not accept any responsibility for injuries or damage resulting from improper use of this product!
Any other use than the description may result in damage to the product. So the dangers are such as electric shock, short circuit, fire etc.
This product is only suited for indoor-use and not for outdoor-use!
We reserve the right to make changes to the product, the packaging or the operating instructions as well as printing errors.
Protect the product from external damage, heavy dirt, moisture and excessive heat!
In order that the warranty claim does not expire please use only the supplied items. Repairs may only be done by an expert and only by using original spare parts!
In commercial institutions, the accident prevention regulations of the professional trade association for electrical equipment and facilities must be adhered to.

Start up

SEBSON TREIBER LED15 LED Driver - FIGURE

Danger: Before installing make sure that the circuit is interrupted! For installation, the work on the mains voltage is required. Remove the associated mains fuse or deactivate the switch fuse! Check by using a voltage tester if the line is de-energized. Make sure that the current circuit will not closed during the installation! There is danger to life here!
Danger: Install the device at least 50cm away from highly inflammable materials such as insulating materials or highly explosive liquids or gases! This is a fire hazard!

Observe the safety instructions and technical data before installing this product!
Choose a vibration-free, dry and non-conductive surface for installation!
To prevent damage to the cables, they must not be strongly bent, pulled or twisted during commissioning!
An electronic protection circuit switches off the LED driver in case of short circuit or overload in the secondary circuit as well as in case of open circuit. After the fault has been rectified, the LED driver is ready for operation again.

Ensure the correct installation of the live and outgoing cables:
Note: The cable to the consumer should not exceed a length of 2m!

Input (PRI): 200-240V AC 50/60Hz (Power supply line)
Output (SEC): 12V DC (LED light/consumer)
Note on installation:
L: Live wire (black or brown)
N: Neutral conductor (blue or grey)

Technical Data:

Model:	TREIBER_LED_15	TREIBER_LED_20
Input voltage:	200-240V AC 50/60Hz
Output voltage:	12V DC +/-0,5V
Output current:	1,25A	1,67A
Maximum power consumption:	15W	20W
Maximum housing temperature:	max. 85°C	max. 85°C
Primary cable:	H03VVH2-F 2×0,75 mm²
Secondary cable:	H03VVH2-F 2×0,75 mm²
Electrical protection:	IP20
Operating temperature:	-20°C – +45°C

Information for private households (WEEE):
The Electrical and Electronic Equipment Act (WEEE) contains a large number of requirements for the handling of electrical and electronic equipment. The most important ones are summarised here.

Separate collection of waste equipment
Old, worn-out or defective electrical and electronic equipment is referred to as waste equipment. These devices must not be disposed of in the normal household waste or together with the residual waste. The devices should be transferred to special collection and return systems.
Batteries and rechargeable batteries as well as illuminants
As a rule, owners of WEEE shall separate spent batteries and accumulators that are not enclosed in the WEEE, as well as light sources that can be removed from the WEEE without causing damage, from the WEEE before handing it over to a collection point. This does not apply if WEEE is prepared for reuse with the participation of a public waste management authority.
Batteries or rechargeable batteries that contain harmful substances are marked with the symbol of a crossed-out dustbin and must not be disposed of in household waste. Below the dustbin symbol is the chemical name of the pollutant – in the example below “Cd” for cadmium. “Pb” stands for lead, “Hg” for mercury:
If disposed of improperly, the substances contained in the batteries may cause hazards to health and the environment.
The hazards are averted by the separate collection and proper disposal of used batteries.
Options for returning old appliances
Owners of WEEE from private households can hand it in free of charge at the collection points of the public waste management authorities or at the take- back points set up by manufacturers or distributors.
Data privacy notice
Old devices often contain sensitive personal data. This applies in particular to information and telecommunications technology devices such as computers and smartphones. In your own interest, please note that each end user is responsible for deleting the data on the end-of-life devices to be disposed of.
Meaning of the “crossed-out dustbin” symbol
The symbol of a crossed-out dustbin regularly displayed on electrical and electronic equipment indicates that the respective device must be collected separately from unsorted municipal waste at the end of its service life.

Cleaning:

Danger: Before start cleaning the product interrupt the current circuit by switching off the circuit breaker or unscrew the fuse! Use a slightly moistened cloth for cleaning. In order not to damage the product, it is essential to avoid water penetrating into the housing! Never clean the device under running water! Do not use solvent-containing cleaner for cleaning.

SEBSON
Sebastian Sonntag
Walter-Behrendt-Str.10
44329 Dortmund
Germany
support@sebson.de
VAT-Nr.: GB179436663
WEEE-Reg.-ID.: 500617