kogan com T3 Pro True Wireless Earbuds User Guide
- June 15, 2024
- Kogan com
Table of Contents
kogan com T3 Pro True Wireless Earbuds
SAFETY & WARNINGS
User Safety Instructions
- To avoid any possible hearing damage, ensure volume is kept at a moderate level.
- Avoid listening to music at loud volume levels for prolonged periods, as this may cause permanent hearing damage or hearing loss.
- Be aware of your surroundings and do not use these earphones while driving, cycling, running or jogging, or when doing any activity which requires your attention and ability to hear.
Product Safety Warning
- For best results and long battery life, always disconnect the USB cable after charging is complete.
- Use an AC adaptor matching the max output voltage and current of the charging case (5V/1A). If the output voltage and current of the adaptor exceed the recommended power, it may cause severe damage to the product and void the product warranty.
- Charge the earphones and the charging case at least once every 6 months.
- Store in a cool and dry place, away from hot and humid conditions.
- The battery is designed to last the lifecycle of the product. It should only be removed by a recycling facility. Any attempt to remove or replace the batteries will damage the product and void the product warranty.
COMPONENTS
OVERVIEW
- Microphone
- Multi-Function Button (MFB)
- LED Indicator (Earphone)
- Charging Case
- LED Indicator (Case)
FITTING
Choosing the Correct Eartip Fit
Three sizes of eartips have been provided to ensure a comfortable fit and good
sound quality. Select the eartips that seal your ear canal properly. You may
need different sized eartips for left and right.
OPERATION
Power On/Off
- To power on the earphones, simply remove the earphones from the charging case. The earphones will automatically turn on if they are charged.
- To power off the earphones, put the earphones back in the charging case.
- If the earphones do not power on, they require further charging.
Interpairing the Earphones
- Ensure that the earphones are sufficiently charged.
- Remove both earphones from the charging case. The earphones will turn on and enter the automatic interpairing mode. Wait a few seconds as both earphones pair with each other. You will hear a prompt tone when the connection is successful. Earphones are normally interpaired within 3-8 seconds.
- To reactivate interpairing mode, simply put the earphones back in the charging case, wait a few seconds and then follow the above procedure again.
Using Left or Right earphones individually
- It is possible to use just one earphone at a time. To do this, the interpairing steps above can be skipped.
- Remove the selected earphone from the charging case, while leaving the other in the case. Close the case.
- The single earphone will turn on and enter the automatic interpairing mode, but not connect to the other earphone.
- It will then be ready to use, with only left or right audio depending on the earphone.
Bluetooth Pairing and Connectivity
After the enter pairing is successful, the earphones are ready to pair with
your Bluetooth-enabled device.
- Turn on the Bluetooth function on your device and search for “T3 Pro” in the Bluetooth menu. Select “T3 Pro” and you will hear a prompt tone when pairing is successful.
- Once the connection is successful, you can start using the wireless earphones.
- To disconnect, simply put the earphones back in the charging case and the earphones will automatically disconnect from any paired devices.
- To reconnect the earphones with the same device, remove the earphones from the charging case and the earphones will automatically connect to your device. Ensure that the Bluetooth function on your device (computer, smartphone, etc) is turned on.
- To prevent the earphones from automatically connecting to a device, remove the earphones from the Bluetooth menu of that device.
- To enjoy calls, music and audio output from your device to the earphones, ensure that the media connection for both calls and media files is activated in the Bluetooth menu.
Using Multi-Function Button (MFB)
| Left earphone (L) | Right earphone (R) |
|---|
P l a y / P a u s e Previous song Next song Volume + Volume –
A n s w e r / E nd a call Reject call
Voice assistant
| Touch once| Touch once
Touch twice
Touch twice
Touch and hold
Touch and hold
Touch once| Touch once
Touch and hold for 3 seconds| Touch and hold for 3 seconds
Touch 3 times
Charging the Earphones
Place the earphones in the charging case. A blue indicator light will turn on inside each earphone when charging. The light will turn off when the earphones are fully charged.
Charging the Case
- To charge the charging case, plug the USB Type-C cable into the charging port of the case and plug the USB end port to a powered USB AC adaptor or computer. Recommended power is DC 5V/1A.
- This device is also compatible with wireless charging pads. Simply place the case on the wireless charger to initiate charging.
- LED light indicators on the charging case will flash blue while charging. When charging is complete the indicator lights will turn solid blue.
Power Save Mode:
The earphones will turn off automatically after 5 minutes if not connected with any device.
Low Battery
- When the battery level is below 3% you will hear a warning voice message: ‘Battery low’. The message is repeated every 20 seconds.
- After 5 minutes of ‘battery low’ warnings, the earphones will power off automatically.
Resetting the Earphones
- Place both earphones into the case, and ensure earphones are in charging mode.
- While the earphones are in the case, long-press the MFB on both earphones for 7 seconds simultaneously, until the blue light blinks three times and turns off.
- Remove both earphones from the case. Both earphones will blink with a blue light. The earphones will automatically attempt to interpair, and you will hear a prompt tone when the connection is successful. Earphones are normally interpaired within 3-8 seconds.
- Delete the device’s record from your phone’s Bluetooth history, then repeat the pairing process.
SPECIFICATIONS
- Bluetooth version **** Bluetooth 5.0 (CVC dual mic noise cancelling)
- Bluetooth chipset **** QUALCOMM QCC3020
- Earphone battery ** 120mAh (x2) (Button cells) Charging case battery ** 400mAh (Li-polymer battery)
- Speaker diameter **** Φ9mm
- Charging time **** Earphone: 2 hours Charging case: 2 hours
- Earphone working time **** Approximately 18 hours (based on 70% volume)
- Charging case capacity **** 24 extra hours in the charging case
- Earphone dimensions **** 25 x 19 x 23.5mm (each)
- Earphone weight 6.5g (each)
- Charging case dimensions 64.2 x 26 x 35mm
- Charging case weight 49g
- Charging port **** USB Type-C (also compatible with wireless charging)
TROUBLESHOOTING
| Problem | Possible Cause | Solution |
|---|
The earphones do not turn on when removed from the case.; the earphones are unresponsive.|
Low battery
|
Fully charge the earphones and the case
No audio after pairing
|
Pairing was unsuccessful
| Reset the earphone and pair again
Earphones turn off automatically|
Low battery
| Fully charge the earphones and the case
Earphones will not charge
|
Power supply error
| Reset the earphones and try charging again
Case LED is off while charging
|
Power supply error
| Check the cable is properly plugged in and power outlet is working
The audio has an echo
| The volume is too high or the environment is too noisy| Adjust volume or change location
Audio drops out
| The environment is too noisy or the device is out of Bluetooth range or obstructed by an obstacle|
Change location and move closer to the paired device
The audio is too low or no audio|
Volume is set too low
| Adjust the volume on your paired device
Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>