Chicco Baby Hug 4 in 1 Air Instruction Manual

June 9, 2024
chicco

Chicco Baby Hug 4 in 1 Air Instruction Manual

INSTRUCTIONS

BABY HUG 4 IN 1 can be used as a crib, reclined cradle, high chair and first chair.

  • Crib mode: suitable from birth until your child is able to sit up unaided (5-6 months), up to a maximum weight of 9 kg.
  • Reclined cradle mode: suitable from birth until your

child learns to sit up unaided (5-6 months approx., weighing a maximum of 9 kg).

  • High chair: permitted when your child is able to sit up unaided (from 6 months ), up to 36 months and weighing a maximum of 15 kg.
  • First Chair at the table mode: Permitted when your

child starts walking and is able to sit down and stand up by himself (about 10/12 months, max. 18 kg).

•  Only for domestic use.

WARNING: TO AVOID DANGER OF SUFFOCATION REMOVE THIS PLASTIC COVER BEFORE USING THE PRODUCT. THIS COVER SHOULD BE DESTROYED OR KEPT AWAY FROM BABIES AND CHILDREN.

  • WARNING: Never leave the child
  • WARNING: Do not allow other children to play unsu- pervised near the
  • WARNING: The product and all of its components must always be assembled by an
  • WARNING: Do not attach any strings to extend the fas-

tening systems of the toybar’s hanging toy and do not make knots/loops: this may cause the accidental forma- tion of slip knots that could cause strangling hazards.

  • Prolonged exposure to direct sunlight may cause the product colours to fade. After prolonged exposure of the product to high temperatures, wait a few minutes prior to putting your child in
  • Make sure that the person using the product knows how to do so in the safest
  • Never use the product without its cover.
  • Do not use the product with more than one child at a
  • Do not leave small objects on the product that could be swallowed by
  • The product  must  only  be  opened,  adjusted  and closed by an
  • Always place the product on a horizontal, stable sur- face when your child is seated in
  • Never place the product near stairs or steps or on
  • Do not hang bags or weights on the product frame as this may affect its
  • Do not open and close the product when your child is sitting in
  • Before assembly, check that neither the product nor any of its components have been damaged during In this case, do not use and keep out of reach of children.
  • Do not use accessories or replacement parts other than those approved by the
  • WARNING: This product must only be used under adult

0 – 6 MONTHS CRIB MODE

IMPORTANT:

READ CAREFULLY AND KEEP FOR FU- TURE REFERENCE.

WARNINGS

WARNING: WHEN IN CRIB MODE, COMPLETELY RE- MOVE THE SAFETY BELTS MAKING SURE THEY ARE KEPT OUT OF YOUR CHILD’S REACH.

  • WARNING: Do not use this product without reading the instructions for use
  • WARNING: The product is intended for use by children aged 0 to 6 months, weighing a maximum of 9 kg.
  • WARNING: Stop using the product as soon as the child can sit or kneel or pull itself up.
  • WARNING: Placing additional items in the product may cause
  • The product must always be placed on a horizontal Never leave the product on a sloping surface with your child inside.
  • WARNING: The product is ready for use only when all

locking mechanisms are engaged. Make sure they are securely engaged before use.

  • WARNING: Do not use the crib if any part is broken, torn or

  • WARNING: DO NOT USE the product in “Crib Configu- ration” and if any part is missing, damaged or broken. Contact Artsana SpA for spare parts and user instruc- tions if needed. DO NOT REPLACE missing, damaged or broken parts with non-OEM components or com- ponents not approved by Artsana

  • WARNING: Be aware of the risk of burns from ciga- rettes, naked flames and other heat sources, like elec- tric or gas heaters, that are near the

  • All components must be firmly fixed in place at all times; also make sure that there are no open zippers as your child’s body parts or clothing could get caught in them (laces, necklaces, pacifier chains etc.), constitut- ing a strangulation hazard.

  • Do not use the body of the crib without its

  • When the product is being used, the wheels must al- ways be

  • The thickness of the mattress must be such that the vertical height (upper surface of the mattress until the upper edge of the product’s sides) is at least 200

  • WARNING: Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc To avoid  strangulation  hazards,  never  give  children objects with strings attached, or leave these objects within their

  • WARNING: Do not use more than one mattress in the Only use the mattress supplied with the crib.

  • WARNING: Only use the mattress sold with the
    Do not add a second mattress, choking hazard. Di- mension mattress 750 x 380 x 30 mm.

  • WARNING: Newborn babies can suffocate on soft bedding. Avoid placing pillows or similar items under newborn babies for additional comfort during

  • Do not leave anything inside the product that might reduce its

  • To prevent the child being trapped, do not place the crib close to walls of

  • The product must be kept away from electrical cables and cords: do not position close to windows where cords, curtains or similar could pose a suffocation or choking hazard. To avoid all risks of strangulation, nev- er give children objects with cords or strings attached, or leave them within their

IMPORTANT! KEEP FOR FUTURE REFER- ENCE.

WARNINGS

  • WARNING: Do not use the reclined cradle once your child can sit unaided, roll over or stand up pushing on their hands, knees and

  • WARNING: Age range: from birth to 9 kg (6 months).

  • WARNING: This reclined cradle is not intended for prolonged periods of

  • WARNING: It is dangerous to use this reclined cradle on an elevated surface, g. a table.

  • WARNING: Always use the restraint

  • Always use the restraint system when your child is in the reclined cradle; adjust the length of the straps as

  • WARNING: Do not use the toybar to carry the reclined

  • WARNING: The reclined cradle is not a substitute for a bed or a crib. If your child needs to sleep they should be placed in a suitable bed or cradle.

  • WARNING: Do not use the reclined cradle if any com- ponents are broken or

  • Never leave the reclined cradle on surfaces that are not perfectly

  • To prevent fire hazards, do not leave the reclined cradle near sources of heat, electrical or gas devices

  • Make sure that all parts are correctly hooked to the mounts.

  • Periodically check for any worn parts, loose screws, worn or unstitched materials and replace any dam- aged parts immediately.

  • Do not place the reclined cradle with your child in it near windows or walls where strings, curtains or other objects could be used by the child to climb or pose choking or strangling hazards.

  • To avoid the risk of your child overbalancing and falling do not place the reclined cradle near windows or

6 – 36 MONTHS HIGH CHAIR

IMPORTANT:

READ CAREFULLY AND KEEP FOR FU- TURE REFERENCE.

WARNINGS

WARNING: IN THIS CONFIGURATION THE TOY- BAR MUST ALWAYS BE POSITIONED BEHIND THE BACKREST.

  • WARNING: Always use the restraint
  • WARNING: Falling hazard: Prevent your child from climbing on the
  • WARNING: Do not use the product unless all compo- nents are correctly fitted and
  • WARNING: Be aware of the risk of open fire and other sources of strong heat in the vicinity of the
  • WARNING: Be aware of the risk of tilting when your child can push its feet against a table or any other
  • WARNING: Make sure that any harness is correctly fit- ted before using.
  • WARNING: Always check the safety and the stability of the high chair before
  • W ARNING : Before using, ensure that all the safety de- vices are fitted and working In particular, make sure that the high chair is locked in the open position.
  • WARNING: Always apply the parking device when it is not being moved.
  • Do not use the high chair until the child can sit up un-
  • The highchair is intended for use for children who can sit up alone and are between 6 and 36 months of age, weighing up to 15 kg.
  • Do not use the high chair if any part is broken, torn or
  • Make sure your child is at a safe distance when open- ing and closing the Make sure that during ad- justment operations (tilting the backrest) the adjusta- ble parts of the high chair do not come into contact with your child.
  • The use of the safety harness with fabric crotch strap correctly fastened to the seat and with crotch bar is necessary to ensure the safety of your child when the chair is used as a high
  • Never move the high chair with your child seated in
  • Do not allow other children to play unsupervised near the high chair, or allow them to climb it.
  • Do not place the high chair near windows or walls where strings, curtains or other objects could be used by the child to climb or pose choking or strangling hazards.

12 M+ FIRST CHAIR MODE

IMPORTANT: READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

  • Age range intended for use: From when your child starts walking and is able to sit down and stand up by himself (about 10/12 months, 18 kg).

  • WARNING: Before using as a chair, remove the safe- ty harness (crotch strap and waist belt) and position them in the relevant spaces. Remove also toy bar or place it behind the

  • WARNING: CHAIR MUST BE USED WITH THE BACK- REST COMPLETELY

  • WARNING: NEVER LEAVE THE CHILD UN- ATTENDED.

  • WARNING: DO NOT place this product near a window

as it can be used as a step by the child and cause the child to fall out of the window.

  • WARNING: Be aware of the risk of open fires and other sources of strong heat in the vicinity of the
  • WARNING: DO NOT place this product near a window where cords from blinds or curtains could strangle a
  • WARNING: Do not use the product if any compo- nents are broken, torn or
  • WARNING: Do not use accessories or replacement parts other than those approved by the
  • Place only on flat and stable
  • WARNING: Check that the space where the chair will be used is free of objects or furniture that may obstruct the product or compromise its correct
  • Do not let your child stand up on the chair to avoid the risk of
  • Do not allow more than one child at a time to sit on the chair in order not to compromise its
  • This chair is intended solely for domestic use and on dry
  • Do not make any modifications: any modification may prejudice its
  • Prolonged exposure to direct sunlight can cause the fabric to After prolonged exposure to high tem- peratures, wait a few minutes before using the product.
  • Never move the chair while the child is seated on

EN 17191: 2021

TIPS FOR CLEANING AND MAINTENANCE

FABRIC COMPOSITION COVER:

Outer cover: 55% Polyester + 45% Cotton  / Padding: 100% Polyester.

BOOSTER CUSHION:

Outer cover: 100% Polyester / Padding: 100% Polyester.

  • Please refer to the care label for instructions on wash- ing the product:

Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean

  • Check that the fabric and stitching are in good condi- tion each time you wash
  • Prolonged exposure to direct sunlight can cause the fabric to

CLEANING

Clean the plastic parts with a soft damp cloth. Never use abrasive detergents or solvents. If the high chair comes into contact with water, dry the metal parts to prevent the formation of rust.

MAINTENANCE

  • This product requires periodical
  • Cleaning and maintenance operations must only be carried out by an
  • Periodically check the product for broken, damaged or missing parts: do not use it in this
  • To avoid friction that may compromise the correct functioning of the product, ensure that all the moving plastic parts located along the metal frame are free of dust, dirt and
  • If necessary, lubricate the moving parts with dry sili- cone
  • Store the product in a dry

COMPONENTS

The product is completely disassembled when pur- chased; check that all of the components listed below are present. If any part is missing contact ARTSANA’s CUSTOMER SERVICES.

The product and all of its components must always be assembled by an adult.
A – Height adjustable pedestal frame A1 – 4 wheels with brakes
A2 – Central support B – Seat frame
C – Seat structure
D – Tubular seat frame
E – Fabric (with shoulder straps) F – Booster cushion
G – Toybar
G1 – Light / sound game buttons G2 – 3 soft toys
I – Upper fabric zips L – Plastic clips
M – Height adjustment pedal N – Backrest recline lever

ASSEMBLY

The product is not assembled when purchased. To use it, carry out the following assembly operations:

  1. The first thing to do is assemble the “A1” wheels on height adjustable base frame “A”. To do this place the frame on a rug or soft surface so as not to damage the floor or frame. Assemble the 4 “A1” wheels inserting the pins in the 4 holes under height adjustable base frame “A” as shown in figure

WARNING: Fully insert the wheel pin into the hole in the base. At this point the base can be rested on the floor.

  1. Insert the fasteners of seat frame “B” into the respec- tive tubes on seat structure “C” until they click into place (Fig. 2).
  2. Assemble the seat (seat frame “B” + seat structure “C”) on the base: insert the two tubes on base “A” into the corresponding holes on seat frame “B” until they click into place (Fig. 3).

WARNING: The backrest must face the height adjust- ment pedal (I) as shown in Fig. 3a.

  1. Insert tube “D” into the corresponding holes on seat frame “B” until they click into place (Fig. 4).
  2. To assemble fabric “E” line up the holes on the fabric with the restraint system installed on seat structure “C”. Pass the two lateral arms of seat frame “B” through the side fabric holes (FIG. 5), insert the pins of the arms into the holes on either side of the backrest (FIG. 5a) until they click into

WARNING: Check that both arms are assembled cor- rectly.

  1. Attach fabric “E” using the two perimeter zips above seat frame “B” (Fig. 6).
  2. Pass the crotch strap and waist straps on seat struc- ture “C” through the holes of fabric “E” (Fig. 7-7a-7b- 7c).
  3. Attach the fabric (E) to the bottom of seat structure “C”, making sure to insert all of the plastic clips in the right slots (Fig. 8-8a).
  4. Press down on the lower part of the seat frame “C” until it locks to the tube on the frame “A” (Fig. 9-9A).
  5. Insert the central support “A2” under the joint of the frame “A” (Fig. 10a-10b). Be sure that the product is not at its maximum height when carrying out this

BOOSTER CUSHION

  1. Reducer cushion “F” is ideal from birth and can be used or removed as To attach it to the

seat, place it on the fabric, pass the crotch strap and waste straps through the holes in booster cushion “F” (reclined cradle mode), (Fig. 11). In high chair mode it is also necessary to pass the shoulder straps through the holes of the booster cushion (Fig. 11a).

TOYBAR

  1. The toys can be attached to the toybar by passing the straps through the plastic openings on the bar (Fig. 12) and fastening the velcro.
  2. Assemble the toybar (with the light positioned to- wards backrest recline lever “N”) inserting the pins of the bar into the holes on seat frame “B” until it clicks into place (Fig. 13).
  3. To incline the toybar in the three possible positions press the side buttons (Fig. 14).
  4. To remove the toybar press the buttons on the inside of the bar support and pull upwards (Fig. 15).

WARNING: This toy must be assembled by adults only. WARNING: Always check that the toybar is properly fastened before using it.

WARNING: To prevent possible injury by entaglement, remove this toy when the child starts trying to get up on its hands and knees in a crowling position.

HEIGHT ADJUSTMENT

  1. Once assembled, the product can be adjusted to various heights in all configurations. To adjust its height, hold down height adjustment pedal “M” (Fig. 16) and lift or lower the seat to the desired

ADJUSTING THE BACKREST

  1. The backrest can be adjusted to four different posi- To do this, push down on backrest recline lever “N” (Fig. 17).

Position 1 – Crib mode (Fig. 17a)
Position 2-3 – Reclined cradle mode (Fig. 17b)
Position 4 – High chair and first chair at the table mode (Fig. 17c)
These adjustments can also be made with your child seated in the product. In this case it will be slightly more difficult.
WARNING: Always check that the backrest is properly locked before use.

USING THE SAFETY HARNESS

  1. With fabric “E” assembled on seat structure “B”, there will be a crotch strap, two waist straps and two shoulder straps (Fig. 18).
  2. CRIB MODE – WARNING: Completely remove all safety harnesses making sure to keep them out of the reach of your child (Fig. 19).
  3. RECLINED CRADLE MODE – WARNING: A 3-point restraint system must be used: crotch strap + waist straps (Fig. 20).
  4. After placing your child in the seat, reclined cradle mode, fasten the straps by passing the two prongs through the crotch strap buckle; adjust the waist straps so that they fit closely around your child’s waist (Fig. 21).
  5. HIGH CHAIR – WARNING: A 5-point restraint sys- tem must be used: crotch strap + waist straps + shoulder straps (Fig. 22).

WARNING: In this configuration the toybar must al- ways be positioned

behind the backrest.

  1. After placing your child in the seat in high chair mode, fasten the straps by passing the two prongs through the shoulder strap buckle (Fig. 23) and then through the crotch strap buckle (Fig. 23a); Adjust the height of the shoulder straps so that they correctly fit your child’s

Always make sure that the straps are fastened correctly. To unfasten the strap, press and pull the side prongs. WARNING : When using the product, always fasten the straps by inserting them in the crotch strap and check that they are tight enough and properly fastened.

24.   FIRST SEAT AT THE TABLE MODE

WARNING: Before using as a chair, remove the safety harness (crotch strap and waist belt) and position them in the relevant spaces (Fig. 24-24A-24B-24C- 24D). Re- move also toy bar or place it behind the backrest.

  1. Adjust the seat to the desired height as indicated in point 16 of the HEIGHT ADJUSTMENT paragraph, the backrest must be completely raised, as indicated in point 17 of ADJUSTING THE BACKREST

WARNING: Always check that the backrest is properly locked before use.
WARNING: When the product is in use, all four casters must be braked.

  1. The safety harness straps can be removed (for washing or for use in the crib/reclined cradle configuration).

To remove the harnesses pull the waist and crotch straps out from the holes in the fabric (Fig. 24-24a-24b) until they are hidden on the seat frame and pull the shoulder straps out from the fabric holes on the backrest (Fig. 24c
24d). After removing the safety harnesses, make sure that the harnesses are correctly re-assembled.
To re-assemble the safety harnesses, carefully follow the steps below:

  1. Follow point 7 of the ASSEMBLY paragraph to re- assemble the waist straps and crotch For the shoulder straps, pass the strap through the hole as shown in Fig. 25, making sure that the length adjust- er is positioned as shown in the figure.

Take the plastic hole of the shoulder straps and pass it through the fabric ring of the harness (Fig. 25a).
Having performed this operation correctly, pull the har- ness downwards until the fabric ring is turned inside out (Fig. 25b-25c).
Once assembled, the belts must be adjusted once again according to the size of your child.

BRAKES

  1. All 4 wheels have brakes; to activate the brakes push down the little lever on the wheels (Fig. 26).
    WARNING: When the product is in use, all 4 wheels must be locked at all times.

To release the brakes push the little levers on the wheels upwards (Fig. 26a).

TOYBAR WITH LIGHTS AND SOUNDS

  1. The toybar comes complete with a sounds and lights panel that is activated by pressing the buttons on the upper section (Fig. 27).

F1 : On button – volume F2 : Plays fun music
F3 : Plays lullabies
F4 : The lights come on

WARNINGS REGARDING TOYBAR ELECTRICAL PARTS

  1. To insert or change the batteries: loosen the screw on the toybar battery compartment cover with a screwdriver and open (FIG. 28). Remove the flat bat- teries and fit new ones, making sure that the battery polarity is correct (as shown on the product); close the battery compartment cover and tighten the screw firmly (2 x 5 V AA batteries).
  • Batteries must only be replaced by an
  • Only use alkaline batteries of the same type or equiva- lent to the type recommended for this product (2 x 5 V AA batteries).
  • Make sure the battery polarity is
  • Never mix new and old or different types of
  • Always keep batteries and tools out of the reach of
  • Do not short-circuit the power
  • Always remove flat batteries from the product to pre- vent any possible liquid leaks from damaging
  • Always remove the batteries if the product will not be used for a long period of
  • Remove the batteries from the toybar before disposing of the
  • Do not throw dead batteries in fire or leave them in the environment; they must be disposed of through waste
  • If the batteries are leaking liquid, replace them im- mediately, making sure to clean the battery compart- ment; thoroughly wash your hands if they have come into contact with the
  • Always dispose of leaking batteries immediately: they can cause burns or other types of
  • Do not try to recharge non-rechargeable batteries: they may
  • The use of rechargeable batteries is not recommended as the toy may not work
  • If using rechargeable batteries, remove them from the toy before recharging
  • Do not leave the product outside in the rain; water will damage the electronic
  • Rechargeable batteries must be charged only under adult

REMOVING THE COVER

  1. To remove the cover from the frame of the product, put the seat in the horizontal position (crib) and unfasten the plastic clips from the seat structure. To do this it is necessary to push the tab inwards and pull the clip down, repeating this procedure for all clips (Fig. 29).
  2. Pull the restraint system out through the fabric holes (if present), see SAFETY HARNESS
  3. Undo the zips along the upper edge (Fig. 30).
  4. Disassemble the lateral arm, pushing the pin inwards and pulling the arm in an outwards direction (Fig. 31). Repeat this procedure for the other arm. Lift the arm (Fig. 32) and remove from the fabric (Fig. 32a).

CLOSING THE PRODUCT

  1. To close the product for storage purposes press down on backrest recline lever “N”, put the backrest in a completely horizontal position and remove the toybar by pressing the buttons (Fig. 33). Complete- ly lower the seat by pressing on height adjustment pedal “M”.

WARNING: The reclined cradle must never be closed with a child sitting in it. Remove your child from the product before closing the frame.

[](https://manuals.plus/wp-content/uploads/2023/04/Chicco-Baby-Hug-4-in-1

-Air-Instruction-Manual_2.png)THIS PRODUCT COMPLIES WITH DIREC- TIVE 2012/19/EU.

The crossed bin symbol on the appliance in- dicates that the product, at the end of its life, must be disposed of separately from domestic waste, either by taking it to a separate waste disposal site for electric and electronic appliances or by returning it to your dealer when you buy another similar appliance. The user is responsible for taking the appliance to a spe- cial waste disposal site at the end of its life. If the dis- used appliance is collected correctly as separate waste, it can be recycled, treated and disposed of ecologically; this avoids a negative impact on both the environment and health, and contributes towards the recycling of the product’s materials.  For  further  information  regarding the waste disposal services available, contact your local waste disposal agency or the shop where you bought the appliance.
Made in China

[](https://manuals.plus/wp-content/uploads/2023/04/Chicco-Baby-Hug-4-in-1

-Air-Instruction-Manual_3.png)WARRANTY

The product is guaranteed against any conformity de- fect in normal conditions of use as provided for by the instructions. The warranty shall not therefore apply in the case of damage caused by improper use, wear or accidental events. For the duration of warranty on con- formity defects please refer to the specific provisions of national laws applicable in the country of purchase, where provided.

Read More About This Manual & Download PDF:

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals