kogan com KAMN40DQUCWA 40 Inch Curved WUHD USB-C Monitor User Guide

kogan com KAMN40DQUCWA 40 Inch Curved WUHD USB-C Monitor

Specifications

• Panel type: IPS
• Resolution: 5120 x 2160
• Curvature: 2500R
• Ports: HDMI, DP, Type-C, USB
• VESA mount: 100x100mm

Assembly

1. Place the monitor on a flat surface with a cloth underneath.
2. Secure the stand stem to the stand base using the provided screws.
3. Slot the assembled stand into the monitor.
4. Lift the monitor by holding the stand and place it on the table.

Adjusting the Angle
Adjust the angle of the monitor for an optimal viewing experience.

SAFETY & WARNINGS

• Read all instructions before using the appliance and retain this user guide for future reference.
• Unplug the monitor before cleaning it with a slightly damp, clean cloth.
• Wiping the screen with a dry microfibre cloth once the monitor has been turned on is recommended.
• Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.
• Do not cover or block the ventilation holes in the monitor casing.
• Do not place the monitor near heaters, stoves, fireplaces or other sources of heat, as well as in rooms lacking adequate ventilation.
• Do not insert any objects or spray any liquid into the vents.
• Do not position the monitor in unsafe locations. If the monitor falls, it may be damaged and may injure nearby people.
• Unplug the monitor if it is not going to be used for an extended period.
• Do not place heavy objects on the monitor, its power cord or any connected cables.
• Do not open the back panel of the monitor, as it contains a high-voltage current even when not plugged in.

COMPONENTS

ASSEMBLY

Stand Assembly

1. Place a cloth or on a flat table. Ensure there are no hard objects, such as screws, on the table.
2. Gently lay the monitor on the cloth with the screen facing down.
3. Secure the stand stem to the stand base using the provided rotary screw.
4. Slot the assembled stand into the monitor. Lift the monitor by holding the stand and place it on the table.

Adjust The Angle
The angle of the screen can be adjusted forward 5°or backward 15° to create the ideal viewing experience.

Notes

• Do not touch or press the screen when adjusting the angle of the monitor.
• The images below are for illustrative purposed only. Actual monitor may differ sUghtly .

Wall Mounting
WARNING: Before installing the monitor on the wall, detach the stand from the monitor.

• To ensure sufficient ventilation, install the monitor at least 10cm away from the wall and leave about 10cm of space on each side of the monitor.
• If you are not confident in wall mounting this product, consult a licensed trade professional.

1. Place a clean, dry and lint-free cloth on a flat, stable surface.
2. Gently lay the monitor on the cloth with the screen facing down.
3. Identify the four wall mounting screw holes on the back of the monitor.
4. Install the wall mounting bracket (not provided) on the back of the monitor and attach the monitor to the wall according to the mounting bracket’s instructions.
5. Ensure that all screws (not provided) are tightened and secured.

VESA mount: 100x100mm
Recommend screw size:

• Plate thickness 2mm – M4x6mm
• Plate thickness 3mm – M4x7mm

Notes :

• Use a wall mounting bracket and screws that conform to VESA standards. Ensure that the box tits appropriately.
• For more information, please refer to the user manual for the wall mounting bracket.
• This monitor model does support wall mounting, however, due to its size, it is recommended to use a stand.

OVERVIEW

1. HDMI
2. DP
3. USB-A
4. Audio out
5. USB USB
6. USB-C 8 DC (Power Input)
7. USB-B
8. USB-A
9. USB-A
10. USB-A

• For best results, an HDMI 2.1 cable is recommended when connecting to the monitor.
• When connecting devices to the monitor, it is recommended to connect the USB-B first. Then, the USB-A ports can be used.
• USB-B is commonly used for printers, monitors and other devices.
• USB-A is commonly used for mice, keyboards, U disks and other devices.

WARNING: Before connecting the monitor to your computer, shut off the power for the computer and the monitor.

Users Controls
Press the power button to turn the monitor on/ off.

Note:
To access the monitor settings, ensure you first have a source connected to one of the monitor ports.

Red – Standby.
Press LEFT| Return to the previous menu level or exit the OSD menu.
Press RIGHT| Enter the OSD menu and confirm key.
Press UP & DOWN| Adjust OSD menu settings.
Press in| Power on/off.

OPERATION

1. Insert one end of the provided DP 1.4 cable into your computer’s graphics card. Insert the other end of the cable into the DP port on your monitor.
2. Connect the power adapter to your monitor and then connect the other end of the power adapter to the power cord. Then, connect the power cord to your power source. It is recommended that you use a surge protector with adequate voltage if a wall outlet cannot be reached directly.
3. Locate the power button on the monitor and press it to turn the monitor on.

FreeSync/ G-Sync

• Ensure your computer has FreeSync/ G-Sync capability, a DP 1.4 port and the latest graphic drivers.
• FreeSync/ G-Sync is on by default when setting 60Hz refresh rate.
• To use FreeSync/ G-Sync, connect your computer and monitor with a DP 1.4 cable.
• After connecting, you will receive a prompt to enable the FreeSync/ G-Sync on your computer. If you do not receive the prompt, you may need to enable the function in your graphics card menu.

PBP/PIP
Wide screen monitors offer Picture-by-Picture (PBP) and Picture-in-Picture (PIP) display modes that allow users to view multiple videos or devices simultaneously on a single monitor. PBP divides the screen into sections, enabling side-by-side display of different video signals from separate sources, while PIP overlays windows on top of each other, useful for tasks like video conferencing. These functions let you connect and display various devices on one monitor, such as a computer and a gaming console, maximising screen real estate and enhancing multitasking or entertainment experiences.

Using the 05D Menu

1. To view the OSD menu, press the power button right.
2. Configure the options by moving the power button up, down, left and right.
3. To return to the previous menu, move the power button left.
4. If you want to exit the OSD menu, move the power button left until you exit.

SPECIFICATIONS

Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

References

• GAN | Delivering your Business Online
• Kogan Help Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>