BOSS AUDIO MPWT60 Marine ATV UTV Roll Cage Waketower Speaker Pods User Manual
- June 5, 2024
- BOSS AUDIO
Table of Contents
BOSS AUDIO MPWT60 Marine ATV UTV Roll Cage Waketower Speaker
Introduction
Your new MPWT60 wake tower speakers are high-power, fully-waterproof 2-way systems featuring 6.5” drivers and a 1” PEI dome tweeter.
What is included?
Before you begin the installation, please check that your product contains the following contents:
- (2) Speaker pods
- (4) 130x14x2mm rubber mounting strips
- (4) 120x14x1mm rubber mounting strips
- (2) 48x30x2mm rubber mounting pads
- (4) 2″ mounting aluminum bands for 2″ and 1.875″ installation
- (4) 1.75″ mounting aluminum bands for 1.75″ and 1.5″ installation
- (4) M6 Locknuts
- (4) M6 flat washers
- (4) M6x60mm screws
Safety considerations when installing
Please remember that these are heavy products that will be installed in a boating environment. These vehicles can travel at high speeds and be unstable. So please consider this and use extreme caution. Some safety considerations include:
- Do not mount the speakers in a location where someone may either walk into or strike their head. During a turbulent ride, please make sure that you do not loosen your footing and fall or hit the unit, or it may cause injury.
- Secure the wires to the speakers in multiple locations along their route to your audio source, so that there are no hanging loops of wire. Having unsecured wires in any hanging conditions can cause entanglement and injury.
- Tighten the aluminum bands with rubber inserts using care. Do not over-compress the rubber inserts. After installation is complete, please recheck all bolts and tighten them further if needed before taking your boat or vessel out for an audio adventure.
- Do not install these speakers where they may block the view of the pilot and prevent safe operation of the vessel or vehicle.
Specifications
- Mid Bass Driver: 6.5″ (165 mm) Poly injection cone Rubber surround
- Tweeter: 1″ (25 mm) PEI dome tweeter
- Crossover network: Built-in
- Impedance: 4 Ohms
- Power Handling : 600 Watts (MAX)
- Frequency Response : 140Hz -20kHz
- Sensitivity: 93dB (1 watt/1 meter)
- Dimensions (W x Hx D): 7.17″ x 9.84″ x 7.32″ (182 x 250x 186 mm)
- Weight (in gift box): 9.7 Ibs (4.4 kg)
Installation instructions
STEP1
To adjust the mounting angle, loosen the metal base of the mounting band by unbolting the two screws. Make sure to put all components of the mounting hardware in a safe location.
STEP2
Twist the metal base to determine the optimal mounting angle for the speaker on the cage bar. Then secure the metal base by tightening the two screws.
STEP3
Place a supplied rubber (48 x 30 mm) pad on the metal base of the mounting band to prevent abrasion and secure clamping.
STEP4
Place two supplied rubber strips around the cage bar to prevent abrasion and secure clamping. Then push two supplied aluminum bands over the cage bar, and align the aluminum bands with the metal base on the speakers.
STEP5
As illustrated, secure the aluminum bands to the metal base using a pair of M6 x 60mm screws, M6 flat washers, and M6 locknuts. The locknuts must be installed into the hex-shaped recess on one end of each aluminum band. Hand- tighten the screws to the degree which allows just enough freedom to rotate the speaker around the cage bar.
STEP6
Speaker installation now completed.
Speaker wiring
Warning:
- For safety, disconnect the negative terminal on the source battery prior to wiring.
- Note your amplifier impedance stability prior to wiring.
- Use only high-quality marine-grade speaker wires. Make sure wires are not squeezed or damaged by sharp edges.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>