MARVEL MWE813 Floor Standing Digital Signage User Guide

June 15, 2024
Marvel

Floor Standing Digital Signage
User Guide(V1.2)

MWE813 Floor Standing Digital Signage

Scan the QR code to open the link in browser.
To get the video guidance of the installation and the usage on YouTube.

https://www.youtube.com/watch?v=42NNOsmvr2c

Attention

  1. Please have a check on the user guide about the operation guidance before using.
  2. Do not splash liquid on the digital signage.
  3. Do not put the digital signage under sunlight directly.
  4. Normal use is protected by our warranty terms. Damage caused by abnormal use is not protected by warranty terms.
  5. If you required with any support from us, please contact our after-sales support team.

Accessories

What’s in Box:

Body & Base

Installation Guidance

  1. Wheels installation on the base(If you don’t want install wheels, jump to next step). Using the cross screw driver to screw in the 4 M6 screws on each wheel.

  2. Put the digital signage body on a bench, and install the base. Use the Allen wrench to screw in the 6 M8 screws to fasten the base.

  3. Put the signage on the floor, get the power connected. And turn the power switch on.

Operation Guidance

  1. Remote controller

  2. The Autoplay application will start up automatically. The quick starting is the Plug and Play Mode function.
    Put your media contents into the USB flash disk root directory. And plug into the digital signage USB port. It will play the media contents automatically.

  3. Also you can make settings on the Autoplay application, set with Copy Mode. Set up a file folder named with “AutoPlayFile” on your USB flash disk. Put your media contents into that “AutoPlayFile”.
    After you plugged your USB flash disk into the digital signage, it will copy the media contents from your USB flash disk “AutoPlayFile” into the digital signage’s internal memory. So that you can plug out your USB flash disk after your media contents was copied successfully to the internal memory.

  4. HDMI Input Supported.
    You can install your player box inside of the digital signal. There’s AC power plug and HDMI input port inside the door available for your player box. Make the settings on digital signage. Set on the “Auto Start Settings”, select the HDMI input, so that it will display the HDMI input signal automatically after the digital signage powered on.

  5. Timer Switch
    You can make auto ON/OFF schedule on the Timer switch application.

After-sales Support
If you have any technical inquiries or need any product services, like software installation, system update and etc..
Please contact us directly.
Email: support@marveltechgroup.com
Phone: 6284885213 (WhatsApp Online)
+8618123978547 (WhatsApp Online)

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference  that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is  encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Marvel User Manuals

Related Manuals