zigbee ECO-DIM.07 Led Dimmer Owner’s Manual

: June 15, 2024
: zigbee

Table of Contents

zigbee ECO-DIM.07 Led Dimmer
Product Information
Product Usage Instructions
Wiring diagram
Setting min. light level
Specifications
Suitable cover plate brands
Installation
Reduction of connection capacity by PowerFactor
Suitable for Zigbee home automation systems
Put dimmer into pairing mode
Reset the dimmer
Documents / Resources

zigbee ECO-DIM.07 Led Dimmer

zigbee-ECO-DIM-07-Led-Dimmer-PRODUCT

Product Information

Specifications

Aansluitvoltage: 220-240 VAC
Frequentie: 50Hz
Dimtechniek: Fase afsnijding (R,C Trailing Edge)
Dimbare led lampen: 0-200W Trailing (R,C), 10-300W
Lampen met elektronische trafo’s: 10-300W
Halogeen- en gloeilampen: Geschikt

Product Usage Instructions

Min. lichtniveau instellen (Setting Minimum Light Level)

Adjust the minimum light level using the dimmer.

FAQ (Frequently Asked Questions)

Q: Is this dimmer suitable for use with magnetic or core transformers?

No, the dimmer is not suitable for use with magnetic or core transformers.

Q: Are retrofit lamps and new installations both compatible with this dimmer?

Yes, this dimmer is suitable for both retrofit lamps and new installations.

Q: What are the compatible brands for the cover material?

The compatible brands for the cover material are Berker by Hager, Kopp, Busch-Jaeger, Merten by Schneider, GIRA, Niko, JUNG, and PEHA. NIKO plate is not included and can be purchased separately on the EcoDim website via ED-10072.

Wiring diagram

Wiring diagram for multiple pulse switches

Setting min. light level

Turn on the lights using the dimmer shaft. Then turn the dimmer shaft as far as possible to the left (minimum light output). Do the lights blink? Then use a screwdriver to slowly turn the MIN potentiometer to the right for stable light.

Is the light already stable?

Then slowly turn the MIN to the left for even better dimmability, to just before the point where the lamps start blinking.
This is the best dimmability of the LED lamps.

Specifications

Connection voltage: 220-240 VAC 50Hz
Frequency: 2,4 GHz, 868 / 915 MHz
Dimming technology: Trailing edge (R, C)
Dimmable LED lamps: 0-200W Trailing (R, C)
Lamps with electronic transformers: 10-300W
Halogen and incandescent lamps: 10-300W
Suitable for both retrofit lamp bulbs and new installations.
Two-wire connection – no neutral wire required.
Soft start system for longer LED lamp life.
Built-in protection for temperature protection and overload.

Note:

This is a two-wire dimmer and it should be connected as shown under the heading ‘Wiring diagram’.
Installation of the dimmer on a 230V main should be carried out by a qualified professional, taking into account national regulations.
Ensure that the electricity is switched off during all work.
You cannot connect more than one dimmer in parallel. To then control the same load from two points.
The dimmer is not suitable for wound/magnetic or core transformers.

Suitable cover plate brands

Berker by Hager
Busch-Jaeger
GIRA
JUNG
Kopp
Merten by Schneider
Niko
PEHA
The NIKO plate is not included. Available separately on the EcoDim website via ED-10072

Installation

Step 1 Always ensure that the electricity is switched off during installation. Then connect the power wires as shown in the ‘Wiring diagram’.
Step 2 Now install the dimmer in the flush-mounting box using the screws.
Step 3 Switch the electricity on again. Turn on the connected lamps using the dimmer shaft.
- Now set MIN as indicated under ‘Setting min. light level’.
Step 4 Now link the dimmer to your SMART home system.
Step 5 Replace the cover frame, the central plate, and the dimmer button on the dimmer.

Reduction of connection capacity by PowerFactor

When calculating the LED connection power of the dimmer, take into account the power factor of the dimmable LED lighting. See the global calculation below for this.

NOMINAL POWER
NUMBER OF LED LIGHT SOURCES
NOMINAL POWER LED / POWER FACTOR.
Example: 10 lamps * (5W per lamp / 0.8 PowerFactor) = 62.5 Watt

Suitable for Zigbee home automation systems

Google Assistant/
Home (Zigbee hub needed)
Amazon Alexa
(Zigbee hub needed)
Philips Hue
HOMEY
FutureHome
Trust
Aduro Smart
Aeotec Smart-Things
WINK
IKEA Dirigera

DOWNLOAD THE APP AT:

Put dimmer into pairing mode

Remove the device from the previous Zigbee network if it has already been added, otherwise, pairing will fail.

Press the reset button twice.

The indicator light starts flashing blue and stays on for 10 seconds when pairing is successful. Timeout 15 minutes.

TouchLink

Reset the dimmer if it is already included in a Zigbee network.
Press the reset button 4 times, the indicator starts flashing green and stays on for 10 seconds.
Bring the remote within 10 cm of the smart dimmer and set the remote to TouchLink.The LED will flash several times on a successful connection
Note: If the dimmer and touchlink device are not connected to a hub, a maximum of 1 touchlink device can be linked. If you want to link multiple touchlink devices, you will always need a Zigbee hub.

Reset the dimmer

Press and hold the reset button for 5 seconds, the indicator will remain red for 10 seconds.
Please note that all configuration parameters will be reset after the device is reset or removed from the network.
EcoDim B.V.
Dr. Huber Noodtstraat 89
7001 DV, Doetinchem, Netherlands (Imported by NJ Trading B.V.)
Made in China

Simplified EU Declaration of Conformity:

We, EcoDim B.V., hereby declare that this product conforms to the directives applicable from the European Union.
The full text of the EU Declaration of Conformity can be consulted at the following internet address: https://www.ecodim.nl/en/service/ecodim-certificering .