zigbee ZGA002 Pico Switch User Manual
- June 15, 2024
- zigbee
Table of Contents
zigbee ZGA002 Pico Switch
Technical Data
- Rated voltage: 110-230V – 50160 Hz
- Max. current: 15A(US), 16A (EU&AU) M M.16
- Operating temperature: 32 – 1040F 1 0-400C
- Operating humidity: 8%-80%
- Radiofrequency: 2.4 Ghz (Zigbee 3.0]
Important safety information
Danger of Electrocution
This device is designed to control external lighting in appliances and operate
in their housing. Faulty connection or mismisuse may result in fire or
electric shock. All installations or modifications on this device must be
performed by a qualified licensed electrician and conform to national
regulations. Even when this device is turned off, voltage may be present at
its terminals. Any wiring maintenance or modifications must always be
performed with the voltage disconnected(disable the fuse). This device must
always use the same L and IN terminal power source.
Caution!
Failure to observe the recommendations included in this manual may be
dangerous or be a violation of the law. Make sure to check the operating
maintenance manual of the device you want to control to make sure the wiring
is safe and allowed. Do not connect devices that are not compliant with the
specification or relevant safety standards. Do not install the device in metal
enclosures or on metal surfaces, this may considerably reduce the range of
wireless operation. Do not expose this product to moisture, water, or other
liquids. Do not use it in bathrooms and other high-humidity rooms. This
product is designed for indoor use only. Do not use outside. This product is
not a toy, keep it away from children and animals!
Please read this and the guide(s) at aeotec.com/support carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or other materials.
-
Switch off the power supply by switch off the main breaker or fuse.
-
Connect the Pico switch according to one of the diagrams:
Fig. 1: Using a single toggle or momentary switch
Fig. 2: Using a double momentary or separate single pole toggle switches (optional – S2 can be used for scene activation] -
Switch back on the power supply.
-
The LED of the Pico Switch should pulse slowly now.
Connecting Pico Switch to your hub
Aeotec Smart Home Hub or SmartThings Hub:
- From the Smart Things dashboard, tap+.
- Tap Add Device, then “By brand”.
- Find and select Aeotec.
- Tap Switch for Dimmer.
- Tap Aeotec Pico Switch [or Aeotec Switch I Dimmer].
- Tap Start, then follow the remaining instructions to pair Pico Switch.
- When prompted by your hub, tap the Action Button on Pico Switch twice, the LED will flash rapidly while it attempts to connect.
- For Home Assistant, Hubitat or other Hubs follow the extended instructions in the QR code below.
Extended Manual:
Connection LED states
If the steps were followed correctly, the LED will change from a rapid flash to one of these LED states depending on success or failure.
- Success: LED will have a solid light based on the state of the switch output [OFF- led off, ON – led on).
- Fail: LED will return to fading in and out.
Default External Switch Mode
The default external switch setting utilizes a general single-pole toggle switch. To change the switch type follow the extended manual to configure Pico Switch, which links you can find by scanning the QR code in the Extended Manual section above.
Not connecting? Try these steps to reset the device
- Press and hold the Action Button for 10+ seconds to manually factory reset the Pico Switch.
- When the LED fades in and out, the reset is successful.
- Try connecting Pico Switch again. Consider a closer location for connecting it, then move it into its installation location.
Need more assistance with the Aeotec Smart Home Hub and automating your
Pico Switch?
Visit aeotec.com/support/ to get more help and
solutions from our knowledge base.
Gateway compatibility.
To see if this Pico Switch is known to be compatible with your ZigBee gateway,
please refer to aeotec.com/compatibility.
US Certifications
FCC ID: 2AOGlZGA002
Tested to Comply With FCC Standards
FOR HOME OR OFFICE USE
Copyright Aeotec Limited. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>