KOHLER 1516306-2-A Wall Sconce Installation Guide
- June 15, 2024
- Kohler
Table of Contents
KOHLER 1516306-2-A Wall Sconce
Record your model number
Thank You for Choosing KOHLER
Need help? Contact our Customer Care Center.
- USA/Canada: 1-800-4KOHLER (1-800-456-4537) Mexico: 001-800-456-4537
- Service parts: kohler.com/serviceparts
- Care and cleaning: kohler.com/clean
- Patents: kohlercompany.com/patents
Warranty
This product is covered under the KOHLER® Indoor Lighting Fixtures Limited Warranty, found at kohler.com/warranty. For a hard copy of warranty terms, contact the Customer Care Center.
Tools and Materials
Plus
- E26 Base G25 Frosted Bulb
Before You Begin
- DANGER: Risk of electric shock. To avoid electrical shock, the electricity must be turned OFF at the circuit breaker or fuse box before beginning installation.
- DANGER: Risk of electric shock. To avoid electrical shock, the electrical outlet box must be properly grounded.
- CAUTION: Risk of property damage. To avoid risk of fire, this fixture has been rated for bulbs up to 60 W. Do not exceed this rating.
IMPORTANT! Do not exceed the recommended wattage. Rated Max 60 W, Type G bulb(s) not included.
- Follow all local plumbing, building, and electrical codes.
- Please read all instructions before you begin.
- The fixture should be installed by a qualified electrician.
- This fixture is for indoor use only.
- Carefully inspect the fixture for damage.
Install the Mounting Plate
- Carefully pull out the wiring from the electrical outlet box and allow the wires to hang down.
- Place the flat side of the mounting plate flat against the electrical outlet box.
- Align the mounting holes on the mounting plate with the holes on the electrical outlet box.
- Securely tighten the mounting plate to the electrical outlet box with the mounting screws.
Connect the Electrical Wires
- Make a loop in the ground wire and wrap around the grounding screw on the mounting plate. Tighten the grounding screw.
- Attach the ground wire (green) from the quick connector to the ground wire (usually bare copper or green) from the electrical outlet box.
- Fasten the ground wires together with the provided wire nut.
- Attach the neutral wire (white) from the quick connector to the neutral wire (usually white) in the electrical outlet box.
- Fasten the neutral wires together with the provided wire nut.
- Attach the hot wire (black) from the quick connector to the hot wire (usually black) in the electrical outlet box.
- Fasten the hot wires together with the provided wire nut.
- Wrap the wire nuts with electrical tape.
- Verify that all plastic wire nuts are securely fastened and strands of bare wire are not exposed.
Install the Fixture
NOTE: Your product may appear different than the one illustrated. The installation procedure is the same.
- Carefully position the wires inside the electrical outlet box behind the mounting plate.
- Connect the quick connector to the fixture.
- Position the fixture over the mounting plate and align the screw holes.
- Secure the fixture to the mounting plate with the provided screws.
Install the Shade(s)
- Remove the socket ring and plastic washer from the socket(s).
- Position the shade(s) on the socket(s), aligning the tab on the shade with the slot in the socket.
- Place the plastic washer on the socket and then hand-tighten the socket ring onto the socket to secure the shade(s).
- Insert the bulb(s) into the socket(s).
- Turn ON the main electrical supply from the main fuse or circuit breaker.
- Confirm the proper operation.
- USA/Canada: 1-800-4KOHLER (1-800-456-4537)
- Mexico: 001-800-456-4537 kohler.com
- 2022 Kohler Co.
References
- How to Use KOHLER Cleaning Products | KOHLER
- Toilets, Showers, Sinks, Faucets and More for Bathroom & Kitchen | KOHLER
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>