KICHLER 52604WHCPZ Sago LED 40 Ceiling Light Instruction Manual

: June 15, 2024
: KICHLER

Table of Contents

FIXTURE DIAGRAM
PARTS LIST
CAUTIONS
INSTALLATION INSTRUCTIONS
FCC INFORMATION
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 52604WHCPZ Sago LED 40 Ceiling Light

KICHLER 52604WHCPZ Sago LED 40 Ceiling Light

FIXTURE DIAGRAM

Fixture Diagram

PARTS LIST

[A] Mounting Strap
[B] Mounting Screw (Qty. 2)
[C] Outlet Box (Not Supplied)
[D] Strap Mounting Screw (Qty. 2)
[E] Lock Washer (Qty. 2)
[F] Knob (Qty. 2)
[G] Canopy
[H] Safety Cable (attached to canopy)

CAUTIONS

CAUTION – RISK OF SHOCK:

Disconnect Power at the main circuit breaker panel or main fuse box before starting and during the installation.

WARNING:

This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

Always be certain that electric current is turned off before cleaning.
Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

Rotate fixture arms into position as shown (Fig. 1).
Find the appropriate threaded holes on mounting strap[A] that align with hole distance in canopy [G]. Assemble mounting screws [B] into threaded holes starting from the outlet box side.
Attach mounting strap to outlet box [C] using the supplied strap mounting screws [D]. Mounting strap can be adjusted to suit position of fixture.
Attach the safety cable[H] to the mounting strap or to the inside of the outlet box and secure into place to prevent damage to the wires during wiring.
Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
Make wire connections. Reference chart below for correct connections and wire accordingly
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|
Neutral Wire
Raise canopy to ceiling, carefully passing mounting screws [B] through mounting screw holes in canopy.
NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and ceiling.
While holding canopy in place, use lock washers [E] and knobs [F] to secure canopy [G]. Tighten to secure.

FCC INFORMATION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.