elk Home 89722-3 3 Light Vanity Light Instruction Manual

: June 15, 2024
: elk HOME

Table of Contents

elk Home 89722-3 3 Light Vanity Light
Product Information
Product Usage Instructions
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elk Home 89722-3 3 Light Vanity Light

Product Information

Specifications

Item #: 89722/3, 89732/3, 89742/3
Power: Requires connection to the main power supply
Usage: Indoor installation only
Wiring Compatibility: Follows National Electrical Code (NEC) and local code specifications

Product Usage Instructions

Installation Precautions

Before starting the installation process, please read and follow these precautions:

Disconnect power at the main fuse box before installation.
Installation should be done by the National Electrical Code (NEC) and all local code specifications.
If you are not familiar with code requirements, it is recommended to hire a certified electrician for installation.

Assembly and Mounting

Hold the mounting bracket (A) with the two holes on the top and bottom, and ensure the head of the attached ground screw is facing outward.
Carefully pull the house wires through the round hole in the mounting bracket (A) and align the holes in the bracket with the junction box holes.
Thread each junction box screw (B) into the corresponding holes in the mounting bracket (A) and junction box. Tighten the screws to secure the mounting bracket to the junction box. Make sure the house wires are pulled completely through the hole in the mounting bracket, avoiding pinching them between the bracket and wall.

Wire Connections

Strip 3/4 of insulation from the ends of the fixture wires.
Slightly loosen the ground screw on the mounting bracket (A), leaving it attached. Wrap the house ground wire (copper) around the ground screw, leaving enough wire to connect it to the fixture ground wire. Twist the ends of the fixture and house ground wires together and secure them with a wire nut (C). Completely tighten the wire nut.
Twist the end of the house lead wire (black) and the fixture lead wire together. Secure them with a wire nut (C). Repeat this step for the house neutral wire (white) and fixture neutral wire. Completely tighten the wire nuts.
Wrap electrical tape (not included) around the wire nuts and wires to ensure a secure connection.
Carefully push all wires and wire nuts into the junction box.

Mounting Backplate

Place the backplate (D) over the mounting bracket (A). Ensure that no wires are pinched between the backplate and wall.

FAQ

Q: What should I do if any parts are missing?
A: Before assembly, remove all parts and part packages from the box. If anything is missing, please contact the retailer from which the product was purchased.
Q: Who should I contact if I have any questions?
A: For any questions, you can call our customer support at 800-613-3261 from Monday to Friday, 8:00AM-6:00PM ET.

WARNING : DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Before assembly, remove all parts and part packages from box. If anything is missing, please get in touch with the retailer from which the product was purchased

INSTALLATION

Hold mounting bracket (A) so the two holes along the edge of the mounting bracket (A) are on the top and bottom of the mounting bracket (A) and the head of the attached ground screw is facing outward.
Carefully pull house wires through the round hole in the mounting bracket (A). Align holes in mounting bracket (A) with holes in junction box.
Thread each junction box screw (B) into holes in the mounting bracket (A) and into holes in the junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box. CAUTION: Make sure house wires are pulled completely through hole in the mounting bracket. DO NOT pinch wires between the mounting bracket and wall.
Strip 3/4” of insulation from ends of fixture wires.
Slightly loosen the ground screw on the mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of the house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:

Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
Twist end of the house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto the ends of the wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
Carefully push all wires and wire nuts into junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green)

with Copper Conductor.

| Insulated Wire (other than green)

with Silver Conductor.

*When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth. The neutral wire is square in shape or ridged.
9. Place backplate (D) over mounting bracket (A).
CAUTION : Do not pinch wires between the backplate and the wall.

Align holes in top and bottom of the backplate (D) with holes in the top and bottom along the edge of the mounting bracket (A). Thread one fixture mounting screw (E) into each hole in top and bottom of backplate (D) and into holes in the mounting bracket (A). Tighten fixture mounting screws (E) to secure the fixture to the wall.
Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify the correct bulb wattage marked on the socket of the fixture.
WARNING : DO NOT exceed maximum bulb wattage.

ANY QUESTIONS CALL : 800-613-3261
M- F 8:00 AM-6:00 PM ET