KICHLER 52561SN Chandelier Ceiling Light Instruction Manual

June 15, 2024
KICHLER

KICHLER 52561SN Chandelier Ceiling Light

KICHLER-52561SN-Chandelier-Ceiling-Light-PRODUCT

FIXTURE DIAGRAM

KICHLER-52561SN-Chandelier-Ceiling-Light-FIG-1 \(1\)

PARTS LIST

  • [A] Stems (2-12”, 2-6” with Short Threaded Tubes
  • [B] installed)
  • [B] Short Threaded Tubes
  • [C] Coupling (on Main Body)
  • [D] Canopy
  • [E] Strap Mounting Screw (Qty. 2)
  • [F] Outlet Box (Not Supplied)
  • [G] Mounting Strap
  • [H] Swivel (attached to Canopy)
  • [I] Mounting Screw (Qty. 2)
  • [J] Lock Washer (Qty. 2)
  • [K] Knob (Qty. 2)
  • [L] Safety Cable (attached to Canopy)
  • [M] Main Body
  • [N] Lower Fixture Arm (attached to Main Body, Qty. 4)
  • [O] Decorative End Cap (Qty. 4)
  • [P] Shades (Qty. 12)

CAUTIONS

CAUTION – RISK OF SHOCK:

  • Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

  1. This fixture is intended for installation per the National
  2. Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
  3. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

  • Always be certain that the electric current is turned off before cleaning.
  • Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

  1. Rotate fixture arms up into a vertical position as shown (Fig. 1).
    • CAUTION: do not rotate fixture arms past the 90-degree position.
  2. Screw decorative end cap[O] onto threads protruding from the bottom of the lower fixture arm[N]. Tighten to secure. Repeat for remaining decorative end caps and lower fixture arms.
  3. Pass fixture wire from coupling[C] on top of a main body[M] through the desired number of short threaded tubes[B] and stems[A]. Screw stems together using short threaded tubes.
    • NOTE: A minimum of one (1) 12-inch (30.5 cm) stem and one (1) 6-inch (15.2 cm) stem[A] must be used when mounting the fixture.
    • NOTE: Thread locking compound must be applied to all stem threads as noted with the (4) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc.
  4. Thread assembled stems into coupling[C] on top of the main body[M].
  5. Pass fixture wire from the last stem through the end of the swivel[H] and into the canopy[D]. Thread the end of the swivel into the end of the last stem. Note the direction of the swivel following the ceiling.
  6. Cut fixture wires a MINIMUM of 20 inches from the top edge of the canopy.
  7. Find the appropriate threaded holes on the mounting strap[G] that align with the hole distance incanopy[D]. Assemble mounting screws[I] into threaded holes starting from the outlet box side.
  8. Attach the mounting strap to the outlet box[F] using the supplied strap mounting screws[E]. The mounting strap can be adjusted to suit the position of the fixture.
  9. Attach the safety cable[L] to the mounting strap or the inside of the outlet box and secure it into place to prevent damage to the wires during wiring.
  10. Grounding instructions: (See Illus. a or b).
    • a. On fixtures where the mounting strap is provided with a hole and two raised dimples, wrap ground wire from the outlet box around the green ground screw, and thread into the hole.
    • b. On fixtures where a cupped washer is provided, attach the ground wire from the outlet box under the cupped washer and a green ground screw, and thread it into the mounting strap. If the fixture is provided with ground wire, connect the fixture ground wire to the outlet box ground wire with a wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
  11. Make wire connections. Reference the chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to: Connect White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer Clear, Brown, Gold or Black with

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) is used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|

Neutral Wire

  1. Raise the canopy to the ceiling, carefully passing mounting screws[I] through mounting screw holes in the canopy.
    • NOTE: Be certain wires do not get pinched between the mounting strap and canopy or canopy and ceiling.
  2. While holding the canopy in place, use lock washers[J] and knobs[K] to secure the canopy[D]. Tighten to secure.
  3. Insert recommended bulbs. (Not supplied).
  4. Shades[P] can be rotated per user preference to change the angle of the lights.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KICHLER User Manuals

Related Manuals