KICHLER 52565CPZBK Black Chandelier Ceiling Light Instruction Manual

We’re here to help866-558-5706
Hrs: M-F 9am to 5pm EST

FIXTURE DIAGRAM

PARTS LIST

[A] Stems (2-12”, 2-6” with Short Threaded Tubes [B] installed)
[B] Short Threaded Tubes
[C] Coupling (on Main Body)
[D] Canopy
[E] Strap Mounting Screw (Qty. 2)| [F] Outlet Box (Not Supplied)
[G] Mounting Strap
[H] Swivel (attached to Canopy)
[I] Mounting Screw (Qty. 2)
[J] Lock Washer (Qty. 2)
[K] Knob (Qty. 2)| [L] Main Body
[M] Upward Socket (Qty. 3)
[N] Downward Socket (Qty. 3)
[O] Small Shade (Qty. 3)
[P] Socket Base (Qty. 3)
[Q] Large Shade (Qty. 3)
---|---|---

CAUTIONS

CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.
WARNING:

1. This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

1. Pass fixture wire from coupling[C] on top of main body[L] through desired number of short threaded tubes[B] and stems[A]. Screw stems together using short threaded tubes.
   NOTE: A minimum of one (1) 12-inch (30.5 cm) stem[A] must be used when mounting fixture.
   NOTE: Thread locking compound must be applied to all stem threads as noted with (4) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc.

2. Thread assembled stems into coupling[C] on top of main body[L].

3. Pass fixture wire from last stem through end of swivel[H] and into canopy[D]. Thread the end of swivel into end of last stem. Note direction of swivel in accordance with ceiling.

4. Cut fixture wires a MINIMUM of 6 inches from the top edge of canopy.

5. Find the appropriate threaded holes on mounting strap[G] that align with hole distance in canopy[D]. Assemble mounting screws[I] into threaded holes starting from the outlet box side.

6. Attach mounting strap to outlet box[F] using the supplied strap mounting screws[E]. Mounting strap can be adjusted to suit position of fixture.

7. Grounding instructions: (See Illus. a or b).
   a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
   b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap. If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps.
   Never connect ground wire to black or white power supply wires.

8. Make wire connections. Reference chart below for correct connections and wire accordingly.
   Connect Black or Red Supply Wire to:| Connect Black or Red Supply Wire to:
   ---|---
   Black| White
   Parallel cord (round & smooth)| Parallel cord (square & ridged)
   Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
   Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

9. Raise canopy to ceiling, carefully passing mounting screws[I] through mounting screw holes in canopy.
   NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and ceiling.

10. While holding canopy in place, use lock washers[J] and knobs[K] to secure canopy[D]. Tighten to secure.

11. While holding upward socket[M] in place, carefully slip preferred shade (small[O] or large[Q]) over upward socket, and screw shade onto threads on base of upward socket. DO NOT OVER-TIGHTEN. Repeat for remaining upward sockets.

12. While holding downward socket[N] in place, carefully slip preferred shade (small[O] or large[Q]) over downward socket, and screw shade onto threads on base of downward socket. DO NOT OVER-TIGHTEN. Repeat for remaining downward sockets.

13. Insert recommended bulbs. (Not supplied).
    NOTE: Socket bases[P] can pivot up to change the angle of light (as shown below):

REV 16-AUG-2022
For warranty information please visit:kichler.com/warranty
IS-52565-US

Documents / Resources

| KICHLER 52565CPZBK Black Chandelier Ceiling Light [pdf] Instruction Manual
52565CPZBK Black Chandelier Ceiling Light, 52565CPZBK, Black Chandelier Ceiling Light, Chandelier Ceiling Light, Ceiling Light, Light
---|---

References

• Kichler® Warranty Information | Kichler Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>