KOHLER K-8304-KS Rite Temp Valve Body and Cartridge Kit Instruction Manual

June 15, 2024
Kohler

KOHLER K-8304-KS Rite Temp Valve Body and Cartridge Kit

KOHLER K-8304KS-Rite-Temp-Valve-Body-and-Cartridge-Kit-
PRODUCT

Specifications

  • Outlet Port: 1/2-14 NPT and 5/8 ID for 1/2 Nominal Copper Tubing
  • Max Finished Wall : 1-15/16 (49 mm)
  • Min Finished Wall : 1-15/16 (49 mm)
  • Inlet Port : 1/2-14 NPT and 5/8 ID for 1/2 Nominal Copper Tubing
  • Maximum (Static) Pressure : 45 psi (3.1 bar)
  • Minimum (Operating) Pressure: 20 psi (1.4 bar)

Features

  • Includes valve body, pressure balance cartridge, rough-in guide, and mudguard
  • 1/2″ Universal NPT and direct sweat inlets and outlets with stops (uninstalled kit)
  • Service stops include integral check valves
  • 5 gpm (18.9 l/min) maximum flow rate at 45 psi
  • Single lever design cycles from off through cold to hot
  •  Antiscald protection
  • One-piece cartridge design simplifies installation and maintenance
  • Adjustable high-temperature limit stop to control maximum water temperature
  • Requires valve trim to complete installation (sold separately)
  • Pressure-balancing diaphragm technology maintains outlet temperature within +/-3°F during water pressure fluctuations

Material

  • Forged dezincification-resistant brass body provides long term reliability and resistance to aggressive water conditions

Installation

  • Designed for use in standard, back-to-back and thin wall installations
  • Valve body features integral mounting locations and symmetrical valve inlets to simplify installation
  • Cartridge is reversible for installations where hot and cold supplies are reversed
  • Rough-in guide designed for both standard and thin wall installations
  • Installed valve rough-in can be flushed and pressure-tested to 150 psi max (air or water) without cartridge by using test cap (sold separately)

Optional Products/Accessories

  • K-10350 Deep rough-in kit
  • K-10351 Test cap for K-8300 Series valve bodies

Codes/Standards

  • ASME A112.18.1/CSA B125.1
  • ASSE 1016/ASME A112.1016/CSA B125.16
  • KOHLER® Faucet Lifetime Limited

Warranty

  • See website for detailed warranty information.

KOHLER K-8304KS-Rite-Temp-Valve-Body-and-Cartridge-
Kit-01

Technical Information

  • All product dimensions are nominal.
  • Shower Valve

Pressure:

  • Maximum (Static) Pressure
  • Minimum (Operating) Pressure

45 psi (3.1 bar) 125 psi (8.6 bar) 20 psi (1.4 bar)

Notes

  • Install this product according to the installation guide.
  • Avoid cross-flow conditions. Do not install shut-off device on either valve outlet.
  • Cap the shower outlet if deck-mount spout, diverter, or handshower is connected to the spout outlet.
  • Install straight pipe or tube drop of 7″ (178 mm) to 18″ (457 mm) with single elbow between the valve and wall-mount spout.
  • For finished walls greater than 3/4″ (19 mm) and less than 1-1/2″ (38 mm), install support(s) 2″ (51 mm) from the stud face.
  • For finished walls greater than 1-1/2″ (38 mm), install support(s) 3″ (76 mm) from the face of the finished wall.

1-800-4KOHLER (1-800-456-4537)

  • Kohler Co. reserves the right to make revisions without notice to product specifications. For the most current Specification Sheet, go to www.kohler.com.
  • 11-11-2023 01:40 – US/CA

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals