VEVOR F270 Tumbler Heat Press User Manual

VEVOR F270 Tumbler Heat Press

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there is any technology or software updates on our product.

Warnings must be followed carefully to avoid body injury.

INTRODUCTION

1. Aluminium alloy handle
2. Pressure adjusting knob
3. Screw
4. LED Display
5. Setting knob
6. Aviation connector
7. Mug heater
8. Power socket

Accessories list

1. Startup
   After power on, short press the start button to start the machine. After startup, the machine will automatically heat up.

2. Shutdown
   Press and hold the start button for 3s to shut down.

3. Auto shutdown
   The machine will automatically shut down if there is no operation within 60 minutes.

Temperature unit conversion

1. In shutdown state
2. Press and hold the start button for 6s.
3. Turn the switch to select the required temperature unit.
4. Short press the start button to start the machine.

Parameter setting

Temperature setting

1. Turn the display half a turn to the right.
2. Enter the temperature setting mode after a beep sound.
3. Turn the switch to the right again to increase the temperature(+).
4. Turn the switch to the left again to reduce the temperature(-).

Time setting

1. Turn the display half a turn to the left.
2. Enter the time setting mode after a beep sound.
3. Turn the switch to the right again to increase the time(+).
4. Turn the switch to the left again to reduce the time(-).

Ready to start Parameter setting

1. Turn the display for a half turn.
2. Enter the setting mode after a beep sound.
3. Set corresponding parameters according to material type.

Start hot stamping

1. Plug in the power cord and turn on the power
2. Short press the start button to start the machine
3. Set printing temperature and time

Hot stamping process

1. Make sure that the machine reaches the set temperature before transfer printing.
2. Stick the picture on the mug
3. Hold the handle and open the machine
4. Put the mugs in from the left and right
5. Press down the handle
6. Press the countdown button to start the countdown

Tips

1. lncrease the transfer time if the colour of the transferred pattern is too light.
2. Reduce the transfer time if the colour of the transferred pattern is too dark.

Pressure adjustment

1. The pressure can be adjusted manually for different sizes of mugs
2. Turn the handwheel clockwise to increase the pressure
3. Turn the handwheel counterclockwise to reduce the pressure

Tips
Please try to keep the pressure balance at both sides.

ELECTRICAL DIAGRAM

1. Main Control Board
2. Connect the cable
3. Power Strip
4. Down temperature sensor
5. Buzzer
6. Thermal cutoff
7. Heating Filament

MAIN BOARD WIRING DIAGRAM

1. 0utput zero line
2. lnput zero line
3. lnput live line
4. 0utput live line
5. Display
6. Temperature probe
7. Sensor switch (backup)

TYPE X CONNECTION

If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

SAFETY INSTRUCTION

Before operating this unit, please read these instructions completely and save them.

Notice

1. Keep it unplugged when moving the machine.
2. Keep unplugged when installing accessories.
3. Place on a flat and stable platform and operate under ventilated conditions.
4. Wear special protective equipment when operating the machine

WARNING

improper use may result in electric shock, fire, personal injury and other damage.

1. Do not use this machine in hazardous locations.
2. Do not use it when the machine is not working properly.
3. Do not allow children or adults who do not understand this manual to operate this machine.
4. Do not disassemble and repair this machine.
5. Do not use an unsuitable AC outlet.
6. Do not touch the heating plate when the machine heating

PRODUCT PARAMETERS

• Name: Mug heat press machine
• Heating method: Electric heating coil
• Rated voltage/frequency: 220-240V~ 50Hz For European users
• Rated voltage/frequency: 120V~ 60Hz For US users
• Rated power: 620W
• Temperature range: 40°C-210°C(104°F-410°F) Time range: 1-999s
• Model: F270
• Press pad size: L 250mm, printing diameter 87mm
• Net weight: 7.0kg
• Gross weight: 7.9 kg
• Outer box size: 375x380x328mm

WARRANTY

COMMON FAULT ANALYSIS

This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste but must be taken to a collection point for recycling electrical and electronic devices.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received. including interference that may cause undesired operation.

CONTACT

• Manufacturer: Yiwu Sun Meta Technology. Co., Ltd
• Address: NO.5 Xinpan Road, Shangxi Toen, Yiwu City, Zhejiang Province, China
• UK Importer: FREE MOOD LTD
• Address: 2 Holywell Lane, London, England, EC2A3ET
• EU Importer: WAITCHX
• Address: 250 bis boulevard Saint-Germain 75007 Paris

EUREP UK LTD

• UNIT2264, 100 OCK STREET,ABINGDON
• OXFORDSHIRE ENGLAND OX14 5DH

EUREP GmbH

• Unterlettenweg 1a, 85051 Ingolstadt, Germany
• E-mail: CustomerService@vevor.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>