cudy LT500 Outdoor Wi-Fi Router Installation Guide
- June 15, 2024
- cudy
Table of Contents
LT500 Outdoor Wi-Fi Router
Installation Guide
LT500 Outdoor Wi-Fi Router
Quick Installation Guide
-
Install the cellular antennas as shown in the picture.
-
Insert the Nano SIM card into the slot until you hear a click.
-
Connect the LAN/WAN (PoE IN) port of the router to the PoE port of the PoE adapter via an Ethernet cable.
-
Plug the PoE adapter into a power outlet.
-
Check the LED status, as long as one bar of signal strength turns solid, your router is successfully connected to the Internet. This process may take 2~5 minutes.
-
Connect to router via ethernet cable or WiFi.
Wired
Connect your computer to the PoE Adapter’s LAN ports via Ethernet cable. Wi- Fi
Connect to router’s WiFi network, WiFi network name and password, listed as below:
WiFi Network Name: Cudy-Outdoor
WiFi Network Name: Cudy-Outdoor-5G
WiFi Password: XXXXXXXX -
Launch a web browser and enter http://cudy.net/ (or http://192.168.10.1/) in the address bar, use admin as password to login.http://cudy.net/
-
Below page would pop up if your SIM card needs PIN to unlock. Please enter your PIN and click “Save & Apply”, then wait 15 seconds to connect to the Internet.
-
Then please check “Cellular” information card of the status page. If the status is connected, means connected to the internet successfully.
-
If cellular is not connected, or if you want to customize the router yourself, click “Quick Setup” and follow the step-by-step instructions to customize the 4G, WiFi or other parameters.
Note:
- If you are not sure about APN parameters, please contact your internet provider.
- ]If you meet any other problems, don’t hesitate to contact our technical support team: support@cudy.com
Enjoy the internet!
LED and Button
Name
| Status| Indication
---|---|---
| /| Strong 4G signal
| /| 4G signal is average
| /| Weak 4G signal
| Off| 5 Ghz WiFi disabled
Flash| 5 Ghz WPS pairing
On| 5 Ghz WiFi enabled
| Off| 2.4 Ghz WiFi disabled
Flash| 2.4 Ghz WPS pairing
On| 2.4 Ghz WiFi enabled
| Off| Not connected to an ethernet device
On| Connected to an ethernet device
| Off| Not connected to the internet
On| Connected to the internet
| Off| Power off
Flash| System boot process
On| Power on
RESET| Press and hold for 5 seconds to take effect.
After taking effect, all LED lights flash 3 times, Then enter the restart
process.
Need Help?
Q1. What should I do if I cannot access the web management page?
A1: If the computer is set to a static IP address, change its settings to obtain an IP address automatically. A2: Make sure http://cudy.net/ or http://192.168.10.1/ is correctly entered in the web browser. A3: Use another web browser and try again. A4: Reboot your router and try again. A5: Disable and enable the active network adapter in use.
Q2. How do I restore the router to its factory default settings?
A1: With the router powered on, press and hold the RESET button for 5 seconds before release. Wait the router resets. A2: Log in to the web management page of the router, and go to Advanced Settings >Reset , click Perform Reset and wait until the reset process is complete.
FCC Statements:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WEEE
According to the EU Directive on Waste Electrical and Electronic Equipment
(WEEE – 2012/19 / EU), this product must not be disposed of as normal
household waste.
Instead, they should be returned to the place of purchase or taken to a public
collection point for recyclable waste. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more information, please contact your
local authority or the nearest collection point. Improper disposal of this
type of waste may result in penalties according to national regulations.
GNU General Public License Notice
The software code in this product was created by third parties and is licensed
under the GNU General Public License (“GPL”). If applicable, Cudy (“Cudy” in
this context refers to the Cudy entity offering respective software for
download or being in charge of the distribution of products that contain
respective code) makes the corresponding GPL source code available upon
request via the official website, either independently or with the assistance
of third parties (such as Shenzhen Cudy Technology Co., Ltd.). For GPL-
related questions, email support@cudy.com. In
addition, Cudy offers a GPL-Code-Centre under
https://www.cudy.com/gplcodecenterdownload where users can get the GPL
source codes used in Cudy products for free. Please note, that the GPL-Code-
Centre is only provided as a courtesy to Cudy’s customers but may neither
offer a full set of source codes used in all products nor always provide the
latest or actual version of such source codes. The GPL code used in this
product is subject to the copyrights of one or more authors and is supplied
WITHOUT ANY WARRANTY.
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. NOTE: This equipment
has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
NEED TECH HELP?
Website: www.cudy.com
Email: support@cudy.com
Driver & Manual: www.cudy.com/download
Support
For technical support, the user
guide and more information, please
visit: https://www.cudy.com/support