ANKER A2620 USB Plug Charger 2-Pack Dual Port User Manual
- June 15, 2024
- Anker
Table of Contents
ANKER A2620 USB Plug Charger 2-Pack Dual Port
Product Information
Specifications
- Input: 100-240 V ~ 0.5 A 50-60 Hz
- USB Output: 5.0 V 2.4 A
- Average active efficiency: 83.4%
- Efficiency at low load (10%): 81.6%
- No-load power consumption: 0.066 W
Product Usage Instructions
Step 1: Power Connection
Connect the PowerPort mini to a power source using the provided power
cable. Make sure the input voltage matches the requirements specified in the
specifications section.
Step 2: USB Device Connection
Connect your USB devices to the USB-A ports on the PowerPort mini. Each
port can deliver up to 2.4 A of current.
Step 3: Power On
Once your USB devices are connected, press the power button or switch on
the PowerPort mini to turn it on.
Step 4: Charging
Your USB devices will start charging once the PowerPort mini is turned on.
The LED indicators on the device may show the charging status of each port.
Step 5: Power Off
To turn off the PowerPort mini, simply press the power button or switch to
the off position.
Frequently Asked Questions (FAQ)
-
Q: Where can I find more information and support?
A: For FAQs and more information, please visit anker.com/support. -
Q: How can I contact customer service?
A: You can contact customer service through the following methods:- Email: support@anker.com
- US Phone: +1 (800)988 7973 (Mon-Fri 6:15 – 17:00 PT)
- UK Phone: +44 (0) 1604 936200 (Mon-Fri 6:00-17:00, Sat-Sun 6:00-14:00)
- DE Phone: +49 (0) 69 9579 7960 (Mo-Fr 6:00 – 11:00)
- JP Phone: +86 400 0550 036 (9:00 – 18:00)
- IT Phone: 03 4455 7823 (9:00 – 17:00)
-
Q: Are there any warranty limitations?
A: Please note that customer rights under applicable consumer sales laws are not affected by the warranties provided under this Limited Warranty.
Using Your Product
- For the fastest and safest charge, use an Anker® cable, your device’s original cable or another certified cable (such as MFi).
Attention
- The product is designed for use with IT equipment only.
- The maximum ambient temperature during use of the appliance must not exceed 35°C
- Naked flame sources, such as candles, must not be placed on the product.
- The disconnection from line voltage is made by AC plug.
- In case of broken cords or plugs, the product must be disposed of.
- If you want to clean the product, only use a dry cloth or brush.
- The socket outlet shall be installed near the equipment and shall be easily accessible.
- The power supply is not intended to be repaired by service personnel in case of failure or component defect (the product can be disposed of).
Specifications
- Input: 100-240 V ~ 0.5 A 50-60 Hz
- USB Output:
- 5.0 V 2.4 A 12.0 W
- (2.4 A Max Per Port)
- Average active efficiency: 83.4%
- Efficiency at low load (10%): 81.6%
- No-load power consumption: 0.066 W
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used by the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
The following importer is the responsible party (for FCC matters only).
- Company Name: Fantasia Trading LLC
- Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
- Telephone: +1-800-988-7973
This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Customer Service
Lifetime technical support.
Please note that your rights under applicable law governing the sale of
consumer goods remain unaffected by the warranties given in this Limited
Warranty.
18-month limited warranty*
support@anker.com
(US) +1 (800)988 7973 Mon-Fri 6:15 – 17:00 (PT)
(UK) +44 (0) 1604 936200 Mon-Fri 6:00-17:00; Sat-Sun 6:00-14:00
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2620
complies with Directive 2014/35/EU & 2014/30/EU & 2011/65/EU & 2009/125/EC.
The full text of the EU Declaration of conformity is available at the
following internet address: https://www.anker.com
Anker Technology (UK) Limited | GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom Anker Innovations Limited: Room
1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Anker
Innovations Deutschland GmbH: Georg-Muche-Strasse 3-5, 80807 Munich, Germany
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2620
complies with Electrical Equipment (Safety) Regulations 2016 & Electromagnetic
Compatibility Regulations 2016 & The Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 &
The Ecodesign for Energy-Related Products Regulations 2010. The full text of
the GB declaration of conformity is available at the following internet
address: https://www.anker.com.
For FAQs and more information, please visit:anker.com/support
Product Number A2620