Blukar K9123 Head Torch Rechargeable User Guide

Blukar LED Headlamp
Model No.: K9123
User Guide

K9123 Head Torch Rechargeable

Physical Diagram

1. Sensor Button
2. Switch Button
3. Headlamp
4. Charging Port
5. Headband
6. Angle Adjustment Plate
7. Sensor Indicator
8. Battery Level Indicator

Welcome

Thank you for purchasing this Blukar product. In order to ensure optimum performance and safety, please read this user manual carefully and keep it for future reference. If you need any additional assistance, please contact our customer support team or send us an email to support@blukar.com.

Packing List

1 x Headlamp
1 x Headband
1 x USB Cable
1 x User Manual

Specifications

On/Off Mode

1. Press the switch button to turn the light on/off and adjust the light mode.
2. In any operating mode, if you select a brightness mode and no operation for more than 8 seconds, the light will directly switch off when you press the button again.

Sensor Mode
Press the sensor button 1 time, the sensor indicator (blue) lights up and enter the sensor mode (Strong White Light).
Press the sensor button 2 times to switch the light (Red Light).
Press the sensor button 3 times to turn off the sensor mode and turn off the light.
Note: waving your hand within 15cm in front of the headlamp to turn on/off the light in sensor mode.

Charging

• Please make sure the product is fully charged when you use it for the first time.
• The four-cell battery indicator shows the corresponding charge level.
• Please use the included or certified USB C cable for charging when the light is dimmed.
• Charging: green light flashing; fully charged: the green light is always on.
• The green light will flash when the headlamp power is weak.

Warning

1. Avoid drops, impact, and extrusion.
2. The high light mode is very bright; in this mode it is normal for the headlamp to heat up. The perceived temperature depends on personal perception and the ambient temperature. The maximum temperature is within the standard limits. The headlamp is safe to use.
3. Do not disassemble and replace the internal parts of the lamp by yourself, so as not to damage the product or even cause safety hazards.
4. The light source of this luminaire is not replaceable and the whole luminaire should be replaced when the light source has reached the end of its life.
5. It is not recommended to leave the product in an uncharged state. If not used for along period of time, charge the headlamp at least once every 3 months.
6. Please use a safety-certified adapter when charging, and never overload the circuit, as this may cause electric shock or fire. Cut off the power in time after fully charged.
7. Do not use this product in extremely hot or cold environments (<25°C/>40°C).
8. Keep it away from water, fire, flammable gas and corrosive liquid.
9. Children should use this product under the supervision and guidance of adults.
10. Do not look directly into the light source to avoid eye irritation.
11. In order to prolong the service life of the battery, please do not overcharge or over discharge.

This product is subject to the provisions of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products identified with this symbol may not be discarded with normal household waste, but must be taken to a collection point for recycling electric and electronic appliances. This recycling symbol marks e.g. an object or parts of the material as valuable for recycling. Recycling helps to reduce the consumption of raw materials and protect the environment.

TEL: 1-800-360-5881
EMAIL: support@blukar.com
WEBSITE: www.blukar.com
© Shenzhen Teng Xun Zhan Yi Technology Co., Ltd. All rights reserved.
Blukar LED Headlamp
Model No.: K9123
Manufacturer : Shenzhen Teng Xun Zhan Yi Technology Co., Ltd.
Manufacturer Address: Room 302, Building 8, Yunli Intelligent Park, Fada Road, Bantian Street, Longgang District, Shenzhen, Guangdong, China

Made in China

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>